Automotive Clips

Product Description

This Rear Bumper Cover Lower Replacement is designed for 2019-2022 Nissan Altima Limited, SL, and Platinum Trims Only with the 6th Gen pre-facelift rear-end configuration and pre-molded 4 backup radar sensor holes. This lower rear bumper cover helps restore the exterior lower fascia area after cracking, impact damage, deformation, scraping, or collision repair. Its molded profile is designed to correspond with the specified rear bumper configuration while retaining the required sensor-hole layout. This listing includes the standalone rear lower bumper cover only – NI1100312 / OEM: 85022-6MA5H, finished in automotive-grade black.

Interchange Part Numbers

Please compare your vehicle trim, rear bumper configuration, sensor layout, and reference numbers with the information below before ordering.

Key Features

• Standalone rear lower bumper cover replacement

• Designed for 2019-2022 Nissan Altima Limited, SL, and Platinum trims

• 6th Gen pre-facelift rear fascia configuration

• Pre-molded with 4 backup radar sensor holes

• Automotive-grade black finish

• Molded profile for the corresponding rear bumper and lower fascia layout

• Suitable for collision repair, exterior restoration, and damaged lower bumper replacement

Technical Fitment Notes

This rear lower bumper cover is intended specifically for the 2019-2022 Nissan Altima 6th Gen pre-facelift Limited, SL, and Platinum configuration. The molded lower fascia profile incorporates 4 pre-molded backup radar sensor holes as part of the bumper design. These openings are an important configuration detail when comparing this replacement with the existing rear bumper component. Important: This component is intended for vehicles equipped with the corresponding 4 backup radar sensor hole configuration. It should not be treated as interchangeable with a smooth non-sensor lower bumper cover or another rear fascia configuration that uses a different sensor-hole or mounting layout. When matched to the correct vehicle and bumper configuration, this lower cover is designed as a direct replacement-style exterior body component for the corresponding mounting locations.

Package Includes

• 1 × Rear Bumper Cover Lower

Total: 1 Piece – Standalone Rear Lower Bumper Cover Only

Important Component Notice

This listing includes only the rear lower bumper cover specifically stated in the Package Includes section. Backup radar sensors, sensor hardware, upper bumper cover, trim pieces, reflectors, brackets, retainers, absorber components, reinforcement bars, exhaust trim components, fasteners, clips, and other surrounding parts are not included unless specifically stated otherwise. The component includes the described pre-molded 4 backup radar sensor holes only. Electronic sensors and related hardware are not included. Product images may show surrounding vehicle components for installation reference or identification purposes only. Please review the Product Description and Package Includes section carefully before purchasing.

Before You Order

Please compare your original rear bumper component, vehicle trim, fascia configuration, sensor-hole layout, mounting points, part shape, and reference numbers with the information provided in this listing before purchase. This listing is for the 2019-2022 Nissan Altima Limited, SL, and Platinum 6th Gen pre-facelift configuration with 4 backup radar sensor holes. Please confirm these features and the listed interchange numbers before ordering.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Nissan Motor Co., Ltd. or Nissan North America, Inc. Nissan® and Altima® are trademarks or registered trademarks of their respective owners. References to vehicle makes, models, trim names, trademarks, OEM numbers, Partslink numbers, Hollander numbers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, production configuration, sensor configuration, mounting points, and existing part before purchase. Please compare the listed reference numbers and original component carefully before ordering.

Product Description

This Rear Bumper Cover Lower Replacement is designed for 2016-2018 Nissan Altima Limited Trims Only with the mid-cycle facelift rear-end configuration and pre-molded 4 backup radar sensor holes. This lower rear bumper cover helps restore the exterior lower fascia area after cracking, impact damage, deformation, or collision repair. Its molded profile is designed to correspond with the specified rear bumper configuration while retaining the required sensor-hole layout. This listing includes the standalone rear lower bumper cover only – NI1100294, finished in automotive-grade black.

Interchange Part Numbers

Please compare your vehicle trim, rear bumper configuration, sensor layout, and reference numbers with the information below before ordering.

Key Features

• Standalone rear lower bumper cover replacement

• Designed for 2016-2018 Nissan Altima Limited trims

• Mid-cycle facelift rear fascia configuration

• Pre-molded with 4 backup radar sensor holes

• Black exterior finish

• Molded profile for the corresponding rear bumper layout

• Suitable for collision repair, exterior restoration, and damaged lower bumper replacement

Technical Fitment Notes

This rear lower bumper cover is intended specifically for the 2016-2018 Nissan Altima Limited mid-cycle facelift configuration. The molded lower fascia profile incorporates 4 pre-molded backup radar sensor holes as part of the bumper design. These openings are an important configuration detail when comparing this replacement with the existing rear bumper component. Important: This component is intended for vehicles equipped with the corresponding 4 backup radar sensor hole configuration. It should not be treated as interchangeable with a smooth non-sensor lower bumper cover or another rear fascia configuration that uses a different sensor-hole or mounting layout. When matched to the correct vehicle and bumper configuration, this lower cover is designed as a direct replacement-style exterior body component for the corresponding mounting locations.

Package Includes

• 1 × Rear Bumper Cover Lower

Total: 1 Piece – Standalone Rear Lower Bumper Cover Only

Important Component Notice

This listing includes only the rear lower bumper cover specifically stated in the Package Includes section. Backup radar sensors, sensor hardware, upper bumper cover, trim pieces, reflectors, brackets, retainers, absorber components, reinforcement bars, fasteners, clips, and other surrounding parts are not included unless specifically stated otherwise. The component includes the described pre-molded 4 backup radar sensor holes only. Electronic sensors and related hardware are not included. Product images may show surrounding vehicle components for installation reference or identification purposes only. Please review the Product Description and Package Includes section carefully before purchasing.

Before You Order

Please compare your original rear bumper component, vehicle trim, fascia configuration, sensor-hole layout, mounting points, part shape, and reference numbers with the information provided in this listing before purchase. This listing is for the 2016-2018 Nissan Altima Limited mid-cycle facelift configuration with 4 backup radar sensor holes. Please confirm these features and the listed interchange numbers before ordering.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Nissan Motor Co., Ltd. or Nissan North America, Inc. Nissan® and Altima® are trademarks or registered trademarks of their respective owners. References to vehicle makes, models, trim names, trademarks, OEM numbers, Partslink numbers, Hollander numbers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, production configuration, sensor configuration, mounting points, and existing part before purchase. Please compare the listed reference numbers and original component carefully before ordering.

Product Description

This Front Bumper Cover Replacement is designed for 2016-2018 Nissan Altima Limited/SL/Platinum Trims with the mid-cycle facelift front-end configuration, pre-molded 2 intelligent front parking radar sensor holes, and tow eye slot. The bumper cover serves as the exterior front fascia shell and is suitable for replacing a cracked, scraped, dented, deformed, or collision-damaged original bumper cover. Its molded profile is designed to correspond with the specified facelift front-end layout while retaining the required sensor openings and tow eye slot configuration. This listing includes the standalone front bumper cover shell only – NI1000306 / OEM: 52119-9HS0H Core Spec, finished in automotive-grade primed black.

Interchange Part Numbers

Please compare your vehicle trim, bumper configuration, sensor layout, and reference numbers with the information below before ordering.

Key Features

• Standalone 1-piece front bumper cover replacement shell

• Designed for 2016-2018 Nissan Altima Limited/SL/Platinum trims

• Mid-cycle facelift front fascia configuration

• Pre-molded with 2 front parking radar sensor holes

• Integrated tow eye slot configuration

• Automotive-grade primed black surface

• Molded profile for the corresponding bumper, grille, and surrounding mounting layout

• Suitable for collision repair, exterior restoration, and damaged bumper replacement

Technical Fitment Notes

This front bumper cover is intended specifically for the 2016-2018 Nissan Altima Limited/SL/Platinum mid-cycle facelift configuration. The fascia profile incorporates 2 pre-molded front parking radar sensor holes and a tow eye slot as part of the bumper shell design. These configuration details are important when comparing this replacement with the existing bumper on the vehicle. Important: This bumper cover is intended for Limited/SL/Platinum Trims with the corresponding 2 front parking radar sensor hole and tow eye slot configuration. It should not be treated as interchangeable with a smooth non-sensor bumper cover or another fascia configuration that uses a different opening or mounting layout. When matched to the correct vehicle and bumper configuration, this cover is designed as a direct replacement-style exterior body component for the corresponding mounting locations.

Package Includes

• 1 × Front Bumper Cover Face Shell

Total: 1 Piece – Standalone Front Bumper Cover Shell Only

Important Component Notice

This listing includes only the front bumper cover shell specifically stated in the Package Includes section. Parking radar sensors, sensor hardware, tow eye components, tow eye cover, grilles, grille inserts, trim pieces, emblems, brackets, retainers, absorber components, reinforcement bars, fog light components, fasteners, clips, and other surrounding parts are not included unless specifically stated otherwise. The bumper cover includes the described pre-molded sensor holes and tow eye slot only. Electronic sensors and related components are not included. Product images may show surrounding vehicle components for installation reference or identification purposes only. Please review the Product Description and Package Includes section carefully before purchasing.

Before You Order

Please compare your original bumper cover, vehicle trim, front fascia configuration, parking sensor layout, tow eye slot, mounting points, part shape, and reference numbers with the information provided in this listing before purchase. This listing is for the 2016-2018 Nissan Altima Limited/SL/Platinum mid-cycle facelift configuration with 2 front parking radar sensor holes and tow eye slot. Please confirm these features and the listed interchange numbers before ordering.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Nissan Motor Co., Ltd. or Nissan North America, Inc. Nissan® and Altima® are trademarks or registered trademarks of their respective owners. References to vehicle makes, models, trim names, trademarks, OEM numbers, Partslink numbers, Hollander numbers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, production configuration, sensor configuration, tow eye configuration, mounting points, and existing part before purchase. Please compare the listed reference numbers and original component carefully before ordering.

Product Overview

Designed for 2022–2025 Toyota RAV4 Limited post-facelift models, this aftermarket rear bumper cover features four pre-molded backup radar sensor holes to match the corresponding flagship rear fascia configuration. Manufactured from durable automotive-grade impact-resistant plastic, the bumper cover is supplied in a black finish and provides a direct replacement solution for rear fascia panels affected by collision damage, cracks, deep scrapes, deformation, or previous repair work.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Sensor & Application Verification

This bumper cover is intended specifically for 2022–2025 Toyota RAV4 Limited post-facelift configurations with four pre-molded rear backup radar sensor holes. Before ordering, compare the sensor-hole count and placement, reflector areas, lower bumper profile, mounting locations, and reference numbers with your original part. Non-sensor versions or other trim configurations may use a different rear fascia.

Components Not Included

This listing includes the rear bumper cover fascia shell only. Backup radar sensors, sensor brackets or retainers, reflectors, lower valance or garnish components, reinforcement parts, mounting hardware, and other surrounding rear bumper accessories are not included unless specifically stated in the package contents.

Finish & Installation

The bumper cover is supplied in a black exterior finish. The surface should be inspected before final installation to determine whether additional preparation or refinishing is required. Test-fit the bumper before final installation to verify sensor-hole positioning, reflector alignment, surrounding panel fitment, and mounting locations. Professional installation is recommended for the best finished result.

Packaging & Shape Recovery

Rear bumper covers are large, flexible exterior panels and may experience minor temporary flexing during packaging or transportation. After unpacking, allow the bumper cover to rest at room temperature and return to its natural contour before test-fitting or refinishing.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

Built for 2022–2025 Toyota RAV4 Limited post-facelift models, this aftermarket front bumper cover features two pre-molded front parking radar sensor holes to match the corresponding premium-trim fascia configuration. The shell is formed from durable automotive-grade impact-resistant plastic and supplied in a primed black finish for professional prep and refinishing. Its sensor-ready layout makes it a practical replacement for front bumpers affected by collision damage, cracks, heavy scrapes, deformation, or prior repair work.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Radar & Fitment Check

This bumper cover is intended specifically for 2022–2025 Toyota RAV4 Limited post-facelift configurations with two pre-molded front parking radar sensor holes. Before ordering, compare the sensor-hole count and placement, grille openings, lower fascia profile, side openings, mounting locations, and reference numbers with your original bumper. Non-sensor or other trim-specific front fascia layouts may require a different cover.

Components Sold Separately

This listing includes the front bumper cover fascia shell only. Parking radar sensors, sensor brackets or retainers, grille components, side bezels or inserts, reinforcement parts, lighting components, emblems, mounting hardware, and other surrounding bumper accessories are not included unless specifically stated in the package contents.

Paint & Installation

The bumper cover is supplied in a primed black, unpainted finish and requires final surface preparation, color matching, and professional painting before installation. Test-fit the fascia before paintwork to verify sensor-hole positioning, grille alignment, and mounting-point fitment. Professional refinishing and installation are recommended for the best final result.

Packaging & Handling

Because front bumper covers are large, flexible exterior panels, minor temporary flexing may occur during packaging or transportation. After unpacking, allow the bumper cover to rest at room temperature and recover its natural contour before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, radar configuration, and existing components before purchase.

Product Overview

This rear bumper cover is designed for 2022–2025 Toyota RAV4 LE & XLE post-facelift models without factory sensor holes, matching the standard rear fascia configuration used on these trims. Manufactured from durable automotive-grade impact-resistant plastic, the cover is supplied in a primed black finish for professional surface preparation and repainting. It provides a clean replacement solution for rear bumpers affected by cracks, scrapes, deformation, collision damage, or previous repair work.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Fitment Confirmation

This bumper cover is intended specifically for 2022–2025 Toyota RAV4 LE & XLE post-facelift configurations without parking sensor holes. Before ordering, compare the rear bumper profile, reflector locations, lower contour, mounting areas, sensor-hole layout, and reference numbers with your original part. Sensor-equipped versions or other trim configurations may use a different rear fascia.

Parts Not Included

This listing includes the rear bumper cover fascia shell only. Reflectors, lower garnish or valance components, parking sensors, sensor brackets, retainers, reinforcement components, mounting hardware, and other surrounding rear bumper parts are not included unless specifically stated in the package contents.

Paint & Installation

The bumper cover is supplied in a primed black, unpainted finish and requires final surface preparation, color matching, and professional painting before installation. Test-fitting before paintwork is strongly recommended to confirm alignment with the quarter panels, reflector areas, and mounting points. Professional installation is recommended, especially when the vehicle has previous rear collision damage.

Packaging & Shape Recovery

Large bumper fascia panels are flexible by design and may show minor temporary movement in shape while packaged or transported. After unpacking, allow the bumper cover to rest at room temperature and return to its natural contour before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

Designed for the updated 2022–2025 Toyota RAV4 LE & XLE post-facelift front-end configuration, this aftermarket bumper cover offers a clean replacement solution for damaged, cracked, scraped, or previously repaired factory fascia panels. The cover is molded from durable automotive-grade impact-resistant plastic and supplied in a primed black finish for professional prep and refinishing. Its standard-trim profile is intended to match the LE/XLE bumper layout while providing a solid foundation for collision repair or cosmetic restoration.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Fitment Verification

This bumper cover is intended for 2022–2025 Toyota RAV4 LE & XLE post-facelift models using the corresponding standard front bumper configuration. Before ordering, compare the bumper contour, grille openings, side insert areas, mounting locations, and reference numbers with the original part on your vehicle. Other trims may use a different fascia layout.

Components Sold Separately

This listing includes the front bumper cover fascia shell only. Grille assemblies, side bezels or inserts, brackets, retainers, reinforcement components, lighting parts, sensors, emblems, mounting hardware, and other surrounding bumper components are not included unless specifically listed in the package contents.

Paint Preparation & Installation

The supplied primed black finish is intended for professional refinishing and is not the vehicle’s final exterior color. Test-fit the bumper before painting to confirm alignment with the surrounding body panels, grille openings, and mounting points. Proper surface preparation, color matching, painting, and professional installation are recommended.

Packaging & Handling

Automotive bumper covers are flexible exterior panels and may experience minor temporary flexing during packaging or transportation. After unpacking, allow the bumper cover to rest at room temperature and recover its natural contour before test-fitting or beginning refinishing work.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, and existing components before purchase.

Product Overview

This aftermarket rear bumper cover is designed for 2019–2021 Toyota RAV4 Limited pre-facelift models equipped with four rear backup radar sensor holes. Made from durable automotive-grade impact-resistant plastic, the fascia comes in a primed black finish for professional preparation and repainting. Its four pre-molded sensor openings are configured for the corresponding Limited-trim rear bumper layout, making it suitable for collision repair, exterior restoration, or replacement of a damaged original fascia.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Sensor & Fitment Check

This rear bumper cover is intended specifically for 2019–2021 Toyota RAV4 Limited pre-facelift configurations with four pre-molded backup radar sensor holes. Before ordering, compare the sensor-hole count and placement, reflector areas, lower bumper contour, mounting points, and reference numbers with your original part. Non-sensor versions or other trim configurations may use a different rear fascia.

Components Not Included

This listing includes the rear bumper cover fascia shell only. Backup radar sensors, sensor brackets or retainers, reflectors, lower garnish or valance pieces, reinforcement components, mounting hardware, and other surrounding rear bumper parts are not included unless specifically stated in the package contents.

Finish & Installation

The bumper cover is supplied in a primed black, unpainted finish intended for professional refinishing. Test-fit the part before painting to confirm sensor-hole positioning, surrounding component alignment, and mounting-point fitment. Proper surface preparation, color matching, painting, and professional installation are recommended.

Packaging & Shape Recovery

Rear bumper covers are large and flexible exterior panels, so minor temporary flexing may occur during packaging or transportation. After unpacking, allow the bumper cover to rest at room temperature and return to its natural contour before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

This aftermarket front bumper cover is configured for 2019–2021 Toyota RAV4 Limited pre-facelift models equipped with two front parking radar sensor holes. Manufactured from durable automotive-grade impact-resistant plastic, the fascia is supplied in a primed black finish for professional preparation and refinishing. The pre-molded dual-sensor layout is intended to match the corresponding Limited-trim front bumper configuration, making it suitable for collision repair, cosmetic restoration, or replacement of a damaged original fascia.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Radar & Fitment Verification

This bumper cover is intended specifically for 2019–2021 Toyota RAV4 Limited pre-facelift configurations with two pre-molded front parking radar sensor holes. Before purchase, compare the sensor-hole count and placement, grille openings, lower fascia profile, side openings, mounting points, and reference numbers with your original bumper. Non-sensor versions or other trim configurations may use a different front fascia.

Components Not Included

This listing includes the front bumper cover fascia shell only. Parking radar sensors, sensor retainers or brackets, grille components, side bezels or inserts, reinforcement parts, lighting components, emblems, mounting hardware, and other surrounding bumper accessories are not included unless specifically stated in the package contents.

Finish & Installation

The bumper cover is supplied with a primed black surface intended for professional painting and refinishing. Test-fit the fascia before paintwork to confirm sensor-hole positioning, grille alignment, and mounting-point fitment. Proper surface preparation, color matching, refinishing, and professional installation are recommended.

Packaging & Handling

Because front bumper fascia panels are large and flexible, minor temporary flexing may occur during packaging or transportation. After unpacking, allow the bumper cover to rest at room temperature and return to its natural contour before test-fitting or beginning paint preparation.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

Restore the rear bodywork of your 2019–2021 Toyota RAV4 LE or XLE with this aftermarket bumper cover, configured for pre-facelift models without factory sensor holes. The fascia is formed from durable automotive-grade impact-resistant plastic and supplied in a primed black finish for professional paint preparation and color matching. It provides a clean replacement option when the original rear bumper has suffered cracks, scrapes, deformation, collision damage, or previous repair work.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Vehicle & Sensor Check

This rear bumper cover is intended for 2019–2021 Toyota RAV4 LE & XLE pre-facelift models without parking sensor holes. Check the original bumper’s sensor layout, reflector locations, lower contour, attachment points, and reference numbers before purchase. Versions equipped with factory sensors or a different trim-specific rear fascia may require another bumper configuration.

Accessories Not Included

Only the rear bumper cover fascia shell is included. Reflectors, lower valance or garnish pieces, parking sensors, sensor brackets, retainers, reinforcement components, installation hardware, and surrounding rear bumper accessories are not included unless specifically stated in the package contents.

Finish & Installation

The primed black surface is preparation-ready and requires final refinishing before installation. Test-fit the bumper first, then complete any necessary surface preparation, paint matching, and final coating. Professional installation is recommended to ensure proper fit around the quarter panels, reflectors, and mounting locations.

Delivery & Shape Recovery

The flexible construction of an automotive bumper fascia may allow minor temporary movement in shape during packaging and transportation. Once unpacked, leave the bumper at room temperature until it returns to its natural contour before beginning fitment checks or paint preparation.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

This aftermarket front bumper cover is made for 2019–2021 Toyota RAV4 LE & XLE pre-facelift models without front sensor holes, providing the correct standard-trim fascia configuration for repair or replacement work. Manufactured from durable automotive-grade impact-resistant plastic, the bumper arrives in a primed black finish ready for professional surface preparation and painting. It is a suitable replacement for original fascia panels affected by collision damage, cracks, deep scratches, deformation, or previous repair work.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Fitment & Sensor Configuration

This bumper cover is intended for 2019-2021 Toyota RAV4 LE & XLE pre-facelift configurations without pre-molded sensor holes. Before ordering, compare your original bumper’s sensor-hole layout, grille openings, side openings, overall contour, mounting locations, and reference numbers. Sensor-equipped or other trim-specific fascia designs may require a different bumper cover.

Components Sold Separately

This listing includes the front bumper cover fascia shell only. Grille assemblies, side bezels or inserts, sensor components, brackets, retainers, reinforcement parts, lighting components, emblems, mounting hardware, and other surrounding bumper parts are not included unless specifically listed in the package contents.

Paint Preparation & Installation

The supplied primed black surface is intended for professional refinishing and is not a final exterior paint finish. Test-fit the bumper before painting to confirm proper alignment with surrounding panels, grille openings, and mounting locations. Final surface preparation, color matching, painting, and professional installation are recommended.

Packaging & Handling

Front bumper covers are flexible exterior body panels and may experience minor temporary flexing while packaged or transported. After unpacking, allow the bumper to rest at room temperature and regain its normal contour before test-fitting or beginning refinishing work.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

Designed for 2016–2018 Toyota RAV4 Limited post-facelift models equipped with four rear backup radar sensor holes, this aftermarket rear bumper cover provides the correct premium-trim fascia layout for collision repair or exterior restoration. Molded from durable automotive-grade impact-resistant plastic, the cover is supplied in a primed black finish for professional preparation and painting. The factory-style sensor-hole layout helps simplify reuse or transfer of the corresponding rear parking-assist components when the original bumper has been cracked, scraped, deformed, or impact damaged.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Sensor & Fitment Verification

This bumper cover is intended specifically for 2016–2018 Toyota RAV4 Limited post-facelift configurations with four pre-molded rear sensor holes. Before ordering, compare the sensor-hole count and placement, reflector areas, lower bumper contour, mounting points, and reference numbers with your existing part. Non-sensor versions or other trim layouts may require a different rear fascia.

Parts Not Included

This listing includes the rear bumper cover shell only. Parking sensors, sensor retainers or brackets, reflectors, lower garnish or valance components, reinforcement parts, mounting hardware, and other surrounding rear bumper components are not included unless specifically listed in the package contents.

Refinishing & Installation

The bumper cover arrives in a primed black, unpainted finish intended for professional refinishing. Test-fit the part before painting to verify the sensor locations, surrounding component alignment, and mounting points. Final surface preparation, color matching, painting, and professional installation are recommended.

Packaging & Handling

Because rear bumper covers are large and flexible, minor temporary flexing can occur during packaging and transportation. After unpacking, allow the panel to rest at room temperature and recover its normal shape before test-fitting or beginning paint preparation.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

Built for the more aggressive front-end layout used on 2016–2018 Toyota RAV4 SE, Limited & Adventure post-facelift models, this aftermarket bumper cover is designed as a replacement for damaged or worn factory fascia panels. The bumper shell is molded from durable automotive-grade impact-resistant plastic and features a primed black surface for professional preparation and painting. Its trim-specific design incorporates the pre-molded lower tab and slotted mounting track configuration required for the corresponding sport and premium bumper layout.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Fitment & Configuration Check

This bumper cover is intended specifically for 2016–2018 Toyota RAV4 SE, Limited & Adventure post-facelift configurations using the corresponding lower tab and slotted track mounting layout. Before ordering, compare the bumper contour, grille openings, lower mounting tracks, side openings, attachment points, and reference numbers with the original part on your vehicle. LE, XLE, or other standard-style bumper layouts may use a different fascia.

Components Sold Separately

This listing includes the front bumper cover fascia shell only. Upper and lower grille components, side bezels or inserts, trim pieces, brackets, retainers, reinforcement components, lighting parts, sensors, emblems, and mounting hardware are not included unless specifically identified in the package contents.

Paint Preparation & Installation

The supplied primed black finish is intended for professional refinishing and is not the vehicle’s final exterior color.Test-fit the bumper before painting to confirm alignment with the grille openings, lower mounting tracks, surrounding body panels, and attachment points. Professional surface preparation, paint matching, refinishing, and installation are recommended.

Shipping & Handling

As a large flexible exterior body panel, the bumper cover may experience minor temporary flexing during packaging or transportation. Allow the part to rest at room temperature and recover its natural contour before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, bumper configuration, and existing components before purchase.

Product Overview

This aftermarket rear bumper cover is tailored for 2016–2018 Toyota RAV4 LE & XLE post-facelift models without factory parking sensor holes. Built from durable automotive-grade impact-resistant plastic, the fascia comes in a primed black finish for professional prep and repainting. It is a practical choice for replacing a rear bumper cover with cracks, scrapes, impact damage, deformation, or previous repair work while preserving the standard LE/XLE rear bumper profile.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Fitment Verification

This version is intended for 2016–2018 Toyota RAV4 LE & XLE post-facelift configurations without parking sensor holes. Before purchase, compare the rear bumper contour, reflector positions, lower openings, mounting locations, sensor-hole layout, and reference numbers with your original part. Sensor-equipped or trim-specific rear bumper designs may require a different fascia.

Components Not Included

This listing includes the rear bumper cover shell only. Reflectors, lower garnish or valance pieces, parking sensors, brackets, retainers, reinforcement components, mounting hardware, and other surrounding rear bumper parts are not included unless specifically listed in the package contents.

Refinishing & Installation

The bumper cover is supplied in a primed black, unpainted finish and requires final surface preparation, color matching, and painting before installation. Test-fitting before paintwork is strongly recommended. Professional body-shop preparation and installation are recommended to help ensure proper alignment and finish quality.

Packaging & Shape Recovery

Rear bumper covers are large, flexible exterior panels and may show minor temporary flexing during packaging or transit. After unpacking, allow the part to rest at room temperature and recover its normal contour before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

Built for the 2016–2018 Toyota RAV4 LE & XLE post-facelift front bumper layout, this aftermarket bumper cover provides a clean replacement option for vehicles with cracked, scraped, impact-damaged, or previously repaired front fascia panels. The shell is manufactured from durable automotive-grade impact-resistant plastic and comes in a primed black finish for professional preparation and repainting. Its trim-specific contour is designed to match the standard LE/XLE front-end configuration while providing a solid foundation for collision repair or cosmetic restoration.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Application Check

This bumper cover is intended for 2016–2018 Toyota RAV4 LE & XLE post-facelift configurations. Before ordering, compare the overall bumper profile, grille openings, side insert areas, mounting points, and reference numbers with your original part. Limited or other trim-specific front bumper layouts may use a different fascia design.

Parts Not Included

This listing includes the front bumper cover shell only. Grilles, side bezels or inserts, brackets, retainers, reinforcement components, lighting parts, sensors, emblems, mounting hardware, and other surrounding front bumper components are not included unless specifically stated in the package contents.

Paint Preparation & Installation

The bumper cover is supplied in a primed black, unpainted finish intended for professional refinishing. Test-fit the fascia before painting to verify alignment with the surrounding panels and mounting locations. Final surface preparation, color matching, painting, and professional installation are recommended for the best finished result.

Packaging & Handling

Because bumper covers are large and flexible exterior panels, minor temporary flexing may occur during packaging or transportation. After unpacking, allow the part to rest at room temperature and return to its normal contour before test-fitting or beginning refinishing work.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, and existing components before purchase.

Product Overview

Designed for 2013–2015 Toyota RAV4 Limited pre-facelift models, this aftermarket front bumper cover features the pre-molded cruise radar sensor opening required for the corresponding flagship trim configuration. The fascia is molded from durable automotive-grade impact-resistant plastic and supplied in a primed black finish for professional surface preparation and repainting. It provides a clean replacement option for front bumper covers affected by collision damage, cracks, deep scrapes, deformation, or prior repair work.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Fitment & Radar Configuration

This bumper cover is intended specifically for 2013–2015 Toyota RAV4 Limited pre-facelift configurations with the corresponding cruise radar sensor opening. Before purchase, compare the radar opening, grille layout, side openings, bumper contour, mounting points, and reference numbers with your original part. LE, XLE, or non-radar bumper layouts may use a different fascia design.

Parts Sold Separately

This listing includes the front bumper cover fascia shell only. Radar sensor hardware, radar brackets, grilles, bezels, trim pieces, reinforcement components, retainers, lighting parts, emblems, and mounting hardware are not included unless specifically listed in the package contents.

Refinishing & Installation

The bumper cover arrives with a primed black surface intended for professional refinishing and should not be considered a final exterior paint finish. Test-fit the bumper before painting to confirm the radar opening, surrounding component alignment, and mounting locations. Professional surface preparation, color matching, painting, and installation are recommended.

Shipping & Handling

As a large flexible exterior body panel, the bumper cover may experience minor temporary flexing during packaging or transit. Allow the part to rest at room temperature and recover its natural contour before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, radar configuration, and existing components before purchase.

Product Overview

This rear bumper cover replacement is designed for 2013–2015 Toyota RAV4 LE & XLE pre-facelift models without parking sensor holes. Formed from durable automotive-grade impact-resistant plastic, the bumper cover is supplied in a primed black finish for professional prep and repainting. Its standard rear fascia layout is intended to replace an original bumper cover that has been cracked, scraped, dented, collision-damaged, or previously repaired.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Fitment Notes

This version is intended for 2013–2015 Toyota RAV4 LE & XLE standard rear bumper configurations without factory parking sensor holes. Before ordering, inspect your original bumper for sensor-hole layout, reflector positions, lower openings, mounting locations, and overall fascia shape. A sensor-equipped bumper or a different trim layout may require another version.

Parts Not Included

The listing includes the rear bumper cover shell only. Reflectors, lower valance or garnish pieces, parking sensors, brackets, retainers, reinforcement components, mounting hardware, and other surrounding rear bumper parts are not included unless specifically stated in the package contents.

Paint Preparation & Installation

The supplied primed black surface is intended for refinishing and is not the vehicle’s final exterior color. Test-fit the bumper before paintwork. Final sanding or preparation, color matching, painting, and professional installation are recommended to help achieve proper alignment and a clean finished appearance.

Shipping & Handling

Due to the size and flexible nature of bumper fascia panels, minor temporary flexing may occur while the part is packaged and transported. After unpacking, allow the bumper cover to rest at room temperature and return to its normal shape before test-fitting or refinishing.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

Designed as a replacement for the standard LE & mid-trim XLE front bumper configuration, this aftermarket bumper cover offers a clean solution for repairing accident damage, deep scratches, cracks, or deterioration to the original fascia. The shell is formed from durable automotive-grade impact-resistant plastic and supplied with a primed black surface, allowing the body shop or installer to complete final preparation and paint matching for the vehicle. Its trim-specific profile is intended to retain the correct bumper contour and surrounding component layout.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Application Verification

Fitment should be confirmed against the vehicle’s trim level, original bumper profile, grille openings, side openings, mounting locations, and reference numbers before purchase. This version is intended for the corresponding LE & XLE standard-style front bumper layout. Other trim packages may use a different fascia design even when the vehicle body appears similar.

Items Sold Separately

Only the front bumper cover fascia shell is included with this listing. Grilles, bumper inserts, side bezels, brackets, retainers, reinforcement parts, lighting components, sensors, emblems, and mounting hardware are sold separately unless specifically identified as included.

Surface Preparation & Installation

The primed black finish is a preparation surface, not the final vehicle color. Test-fit the bumper before refinishing to confirm alignment with the surrounding panels and attachment points. Final sanding or surface preparation, paint matching, and professional refinishing are required prior to installation. Body-shop installation is recommended for the best fit and finished appearance.

Handling After Delivery

Automotive bumper covers are flexible by design. Temporary movement or slight distortion can occur while the panel is packaged and transported. Once unpacked, allow the bumper cover to rest at room temperature and regain its normal contour before test-fitting or beginning paint preparation.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and related vehicle trademarks are the property of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, and existing components before purchase.

Product Overview

Replace a damaged or worn rear fascia with this aftermarket rear bumper cover, engineered for 2020–2022 Toyota Corolla SE & XSE pre-facelift models. Designed around the more aggressive SE/XSE rear profile, this bumper cover is molded from durable automotive-grade impact-resistant plastic and supplied in a primed black finish for professional prep and painting. It is well suited for collision repair, cosmetic restoration, or replacing a factory bumper cover with cracks, scrapes, deformation, or prior repair damage.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Fitment Verification

This rear bumper cover is designed specifically for 2020–2022 Toyota Corolla SE & XSE pre-facelift configurations. Before ordering, compare the overall bumper contour, lower rear openings, reflector positions, mounting points, and reference numbers with the original part on your vehicle. Standard-trim Corolla rear bumper designs may differ from the SE/XSE configuration.

Parts Not Included

This listing is for the rear bumper cover fascia shell only. Lower valance or diffuser-style trim, reflectors, brackets, retainers, reinforcement components, sensors, mounting hardware, and other surrounding rear bumper parts are not included unless specifically stated in the package contents.

Paint & Installation

The bumper cover is supplied in a primed black, unpainted finish and is intended to be professionally refinished to match the vehicle.  Test-fitting before paintwork is strongly recommended. Proper surface preparation, color matching, and professional installation help ensure accurate alignment and a clean finished appearance.

Shipping & Shape Recovery

As a large flexible exterior panel, the bumper cover may experience minor temporary flexing during transit. After unpacking, allow the part to rest at room temperature and recover its natural shape before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, and existing components before purchase.

Product Overview

Bring the front of your Corolla back to a clean, sport-oriented appearance with this aftermarket front bumper cover, developed for 2020–2022 Toyota Corolla SE & XSE pre-facelift models. Manufactured from durable automotive-grade impact-resistant plastic, the fascia is supplied in a primed black finish for professional prep and painting. Its SE/XSE-specific design makes it a strong replacement choice for collision damage, cosmetic wear, or previously repaired bumper covers that no longer align or present properly.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Confirm Fitment Before Purchase

This bumper cover is intended specifically for 2020–2022 Toyota Corolla SE & XSE pre-facelift configurations. Before ordering, compare your original bumper’s overall contour, grille openings, side bezel areas, mounting tabs, and reference numbers. SE/XSE bumper layouts differ from standard-trim Corolla configurations.

Components Not Included

This listing includes the front bumper cover shell only. Upper and lower grilles, side bezels or inserts, brackets, retainers, reinforcement components, lighting parts, sensors, emblems, mounting hardware, and other surrounding bumper components are not included unless specifically listed in the package contents.

Refinishing & Installation

The bumper is supplied in a primed black, unpainted finish intended for professional refinishing. Test-fit the fascia before painting, then complete the necessary surface preparation, color matching, and final paintwork. Professional installation is recommended to help ensure proper panel alignment and fit.

Packaging Note

Because bumper covers are large and flexible, minor temporary flexing may occur during transportation. After unpacking, allow the fascia to rest at room temperature and recover its natural shape before test-fitting or refinishing.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. References to vehicle makes, models, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, and existing components before purchase.

Product Overview

Replace a worn or damaged rear fascia with this aftermarket rear bumper cover, developed for 2020–2022 Toyota Corolla L, LE, XLE & Hybrid pre-facelift configurations. Molded from durable automotive-grade impact-resistant plastic, the bumper cover is supplied in a primed black finish for professional preparation and color matching. Its trim-specific rear profile makes it a suitable replacement for collision repairs, cosmetic restoration, or heavily damaged original bumper covers.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Verify Your Application

This rear bumper cover is intended for 2020–2022 Toyota Corolla L, LE, XLE & Hybrid pre-facelift models. Before ordering, compare the rear bumper profile, lower openings, reflector positions, mounting areas, and reference numbers with the original part on your vehicle. Different trim configurations may use different rear fascia designs.

Components Not Included

This listing is for the rear bumper cover shell only. Reflectors, lower valance or garnish pieces, brackets, retainers, reinforcement components, sensors, mounting hardware, and other surrounding rear bumper parts are not included unless specifically identified in the package contents.

Refinishing & Installation

The primed black surface is intended for refinishing and is not a final exterior paint finish. Test-fit the bumper before painting, then complete the required surface preparation, color matching, and refinishing. Professional body-shop installation is recommended, particularly when surrounding mounting points have previous collision damage.

Packaging & Shape Recovery

Rear bumper covers are large, flexible exterior panels and may experience minor temporary flexing during transportation. After unpacking, allow the bumper cover to rest at room temperature and return to its natural shape before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, and existing components before purchase.

Product Overview

Bring the front of your 2020–2022 Toyota Corolla L, LE, or XLE back to a clean, repair-ready condition with this aftermarket bumper cover fascia. Designed around the pre-facelift standard-trim front bumper layout, the shell is manufactured from durable automotive-grade plastic and supplied in a primed black finish for professional refinishing. It is well suited for collision repairs, cosmetic replacement, or vehicles with cracked, scraped, or heavily worn original bumper covers.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Confirm Fitment Before Ordering

This bumper cover is intended for 2020–2022 Toyota Corolla L, LE & XLE pre-facelift configurations. Before purchase, compare your original bumper’s overall profile, grille openings, side openings, mounting tabs, and reference numbers. Trim-specific bumper layouts may differ even within the same model year.

Components Sold Separately

This listing is for the bumper cover shell only.  Grilles, side bezels or inserts, brackets, retainers, reinforcement bars, lighting components, sensors, emblems, and installation hardware are not included unless specifically identified as part of the package.

Refinishing & Installation

The supplied primed black surface is not a final exterior finish. The bumper should be test-fitted before painting, followed by proper surface preparation, color matching, and refinishing. Professional installation is recommended, particularly when the vehicle has prior collision damage or surrounding mounting points require adjustment or replacement.

Packaging Note

Large automotive fascia panels are naturally flexible and may show temporary movement in shape during transportation. After unpacking, place the bumper in a suitable indoor environment and allow it to settle into its normal form before test-fitting or refinishing.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, and existing components before purchase.

Product Overview

Refresh the rear appearance of your Corolla with this aftermarket rear bumper cover replacement, designed specifically for 2017–2019 Toyota Corolla SE & XSE facelift models. Made from durable automotive-grade impact-resistant plastic, this rear fascia shell comes in a primed black finish for professional preparation and painting. It is a practical solution for replacing a cracked, scraped, impact-damaged, or previously repaired factory bumper cover while maintaining the sportier SE/XSE rear-end styling.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Fitment Check Before Purchase

Please confirm your vehicle year, SE/XSE trim configuration, rear bumper profile, lower openings, reflector locations, mounting points, and reference numbers before ordering. This bumper cover is designed specifically for 2017–2019 Toyota Corolla SE & XSE facelift configurations and is not intended for LE, XLE, or other rear bumper layouts.

What’s Not Included

This listing includes the rear bumper cover fascia shell only. Lower valance or garnish components, reflectors, brackets, retainers, reinforcement components, mounting hardware, and other surrounding rear bumper accessories are not included unless specifically listed in the package contents.

Paint & Installation Notice

The bumper cover is supplied in a primed black, unpainted finish and requires final surface preparation, paint matching, and refinishing before installation. Test-fitting before painting is strongly recommended. Professional body-shop preparation and installation are recommended to help ensure proper alignment and finish quality.

Shipping & Packaging Note

Because automotive bumper covers are large and flexible, minor temporary flexing may occur during transportation. After unpacking, allow the bumper cover to rest at room temperature and recover its natural shape before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. References to vehicle makes, models, trademarks, OEM numbers, Partslink numbers, Hollander identifiers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, and existing part before purchase.

Product Overview

Upgrade the front appearance of your Corolla with this aftermarket front bumper cover, designed for 2017–2019 Toyota Corolla SE & XSE facelift models. Made from durable automotive-grade impact-resistant plastic, this fascia shell comes in a primed black finish for professional preparation and painting. It is well suited for replacing a cracked, scraped, collision-damaged, or previously repaired factory bumper cover while preserving the sharper SE/XSE front-end styling.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Fitment Check Before Purchase

Please confirm your vehicle year, SE/XSE trim configuration, bumper profile, grille and bezel openings, mounting locations, and reference numbers before ordering. This bumper cover is designed specifically for 2017–2019 Toyota Corolla SE & XSE facelift configurations and is not intended for LE, XLE, or other bumper layouts.

What’s Not Included

This listing includes the front bumper cover fascia shell only. Upper and lower grille components, side inserts or bezels, brackets, retainers, reinforcement components, lighting parts, mounting hardware, and other surrounding front bumper accessories are not included unless specifically listed in the package contents.

Paint & Installation Notice

The bumper cover is supplied in a primed black, unpainted finish and requires final surface preparation, paint matching, and refinishing before installation. Test-fitting before painting is strongly recommended. Professional body-shop preparation and installation are recommended to help ensure proper alignment and finish quality.

Shipping & Packaging Note

Because automotive bumper covers are large and flexible, minor temporary flexing may occur during transportation.  After unpacking, allow the bumper cover to rest at room temperature and recover its natural shape before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. References to vehicle makes, models, trademarks, OEM numbers, Partslink numbers, Hollander identifiers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, and existing part before purchase.

Product Overview

Give your Corolla’s rear end a clean, factory-style refresh with this aftermarket rear bumper cover, developed for 2017–2019 Toyota Corolla LE & XLE trim configurations. Made from durable automotive-grade impact-resistant plastic, this 1-piece fascia shell is supplied in a primed black finish for professional prep and painting. It is a practical replacement for bumper covers affected by cracks, scrapes, impact damage, or previous body repair.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Fitment Check Before Purchase

Confirm your vehicle year, trim level, bumper profile, mounting locations, and reference numbers before ordering.This rear bumper cover is intended for 2017–2019 Toyota Corolla LE & XLE configurations. Compare the lower openings, reflector areas, and mounting points with your original bumper to help confirm the correct application.

What’s Not Included

This listing is for the rear bumper cover shell only. Reflectors, lower garnish or valance pieces, brackets, retainers, reinforcement components, mounting hardware, and other surrounding rear bumper parts are not included unless specifically listed in the package contents.

Paint & Installation Notice

The bumper cover is supplied in a primed black, unpainted finish and requires final surface preparation, paint matching, and refinishing before installation. Test-fitting before painting is strongly recommended. Professional body-shop preparation and installation are also recommended to help ensure proper alignment and finish quality.

Shipping & Packaging Note

Because bumper covers are large and flexible, minor temporary flexing may occur during transportation. After unpacking, allow the bumper cover to rest at room temperature and recover its natural shape before test-fitting or refinishing.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, Hollander identifiers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, and existing part before purchase.

Product Overview

Refresh the front appearance of your Toyota Corolla with this direct-fit aftermarket bumper cover, engineered for LE & XLE trim configurations. Built from durable automotive-grade impact-resistant plastic, this 1-piece fascia shell comes in a primed black finish and is ready for professional surface preparation and painting. It offers a clean replacement solution for worn, cracked, scraped, or collision-damaged factory bumper covers while maintaining the vehicle’s original front-end styling.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Before You Order

Please verify your vehicle year, trim configuration, front bumper design, and reference numbers before purchasing. Compare the bumper shape, grille and bezel openings, mounting points, and reference numbers with your existing part to confirm compatibility. Designed specifically for Toyota Corolla LE & XLE bumper configurations. Not intended for other bumper or trim configurations.

What’s Not Included

This listing includes the front bumper cover fascia shell only. Upper and lower grille components, side inserts or bezels, brackets, retainers, reinforcement components, lighting parts, and mounting hardware are not included unless specifically stated in the package contents.

Paint & Installation Notice

This bumper cover is supplied in a primed black, unpainted finish and requires surface preparation and professional painting before final installation. Professional test-fitting, paint preparation, color matching, and installation are recommended. Existing mounting hardware and surrounding bumper components should be inspected before installation and replaced when necessary.

Shipping & Packaging Note

Due to the size and flexible construction of automotive bumper covers, minor temporary flexing may occur during shipping. Allow the bumper cover to return to its natural shape at room temperature before test-fitting, preparation, and painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. References to vehicle makes, models, trademarks, OEM numbers, Partslink numbers, interchange numbers, Hollander identifiers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, and existing part before purchase.

Product Overview

Restore your Toyota Corolla’s rear exterior appearance with this aftermarket rear bumper cover replacement, designed specifically for 2014–2016 Toyota Corolla S & Special Edition pre-facelift trims. Constructed from durable automotive-grade impact-resistant plastic, this rear bumper fascia shell features a primed black finish and is ideal for replacing a cracked, scraped, damaged, or collision-worn original bumper cover.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Before You Order

Please verify your vehicle year, trim configuration, rear bumper design, and reference numbers before purchasing. Compare the bumper shape, lower openings, reflector locations, mounting points, and reference numbers with your existing part to confirm compatibility. Designed specifically for 2014–2016 Toyota Corolla S & Special Edition pre-facelift trims. Not intended for L, LE, LE Eco, or other bumper configurations.

What’s Not Included

This listing includes the rear bumper cover fascia shell only. Lower valance or garnish components, reflectors, brackets, retainers, reinforcement components, and mounting hardware are not included unless specifically stated in the package contents.

Paint & Installation Notice

This bumper cover is supplied in a primed black, unpainted finish and requires surface preparation and professional painting before final installation. Professional test-fitting, paint preparation, color matching, and installation are recommended. Existing mounting hardware and surrounding bumper components should be inspected before installation and replaced when necessary.

Shipping & Packaging Note

Due to the size and flexible construction of automotive bumper covers, minor temporary flexing may occur during shipping. Allow the bumper cover to return to its natural shape at room temperature before test-fitting, preparation, and painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. References to vehicle makes, models, trademarks, OEM numbers, Partslink numbers, interchange numbers, Hollander identifiers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, and existing part before purchase.

Product Overview

Restore your Toyota Corolla’s front-end appearance with this aftermarket front bumper cover replacement, designed specifically for 2014–2016 Toyota Corolla S & Special Edition pre-facelift trims. Constructed from durable automotive-grade impact-resistant plastic, this front bumper fascia shell features a primed black finish and is ideal for replacing a cracked, scraped, damaged, or collision-worn original bumper cover.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Before You Order

Please verify your vehicle year, trim configuration, front bumper design, and reference numbers before purchasing. Compare the bumper shape, grille and bezel openings, mounting points, and reference numbers with your existing part to confirm compatibility. Designed specifically for 2014–2016 Toyota Corolla S & Special Edition pre-facelift trims. Not intended for L, LE, LE Eco, or other bumper configurations.

What’s Not Included

This listing includes the front bumper cover fascia shell only. Upper and lower grille components, side inserts or bezels, brackets, retainers, reinforcement components, lighting parts, and mounting hardware are not included unless specifically stated in the package contents.

Paint & Installation Notice

This bumper cover is supplied in a primed black, unpainted finish and requires surface preparation and professional painting before final installation. Professional test-fitting, paint preparation, color matching, and installation are recommended. Existing mounting hardware and surrounding bumper components should be inspected before installation and replaced when necessary.

Shipping & Packaging Note

Due to the size and flexible construction of automotive bumper covers, minor temporary flexing may occur during shipping. Allow the bumper cover to return to its natural shape at room temperature before test-fitting, preparation, and painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. References to vehicle makes, models, trademarks, OEM numbers, Partslink numbers, interchange numbers, Hollander identifiers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, and existing part before purchase.

Product Overview

Restore your Toyota Corolla’s rear exterior appearance with this aftermarket rear bumper cover replacement, designed specifically for 2014–2016 Toyota Corolla L, LE, and LE Eco pre-facelift trims. Constructed from durable automotive-grade impact-resistant plastic, this rear bumper fascia shell features a primed black finish and is ideal for replacing a cracked, scraped, damaged, or collision-worn original bumper cover.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Before You Order

Please verify your vehicle year, trim configuration, rear bumper design, and reference numbers before purchasing. Compare the bumper shape, lower openings, reflector locations, mounting points, and reference numbers with your existing part to confirm compatibility. Designed specifically for 2014–2016 Toyota Corolla L, LE, and LE Eco pre-facelift trims. Not intended for other bumper or trim configurations.

What’s Not Included

This listing includes the rear bumper cover fascia shell only. Lower valance or garnish components, reflectors, brackets, retainers, reinforcement components, and mounting hardware are not included unless specifically stated in the package contents.

Paint & Installation Notice

This bumper cover is supplied in a primed black, unpainted finish and requires surface preparation and professional painting before final installation. Professional test-fitting, paint preparation, color matching, and installation are recommended. Existing mounting hardware and surrounding bumper components should be inspected before installation and replaced when necessary.

Shipping & Packaging Note

Due to the size and flexible construction of automotive bumper covers, minor temporary flexing may occur during shipping. Allow the bumper cover to return to its natural shape at room temperature before test-fitting, preparation, and painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. References to vehicle makes, models, trademarks, OEM numbers, Partslink numbers, interchange numbers, Hollander identifiers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, and existing part before purchase.

Product Overview

Restore your Toyota Corolla’s front-end appearance with this aftermarket front bumper cover replacement, designed specifically for 2014–2016 Toyota Corolla L, LE & LE Eco pre-facelift models. Constructed from durable automotive-grade impact-resistant plastic, this front bumper fascia shell features a primed black finish and is ideal for replacing a cracked, scraped, damaged, or collision-worn original bumper cover. Suitable for collision repair, cosmetic restoration, and body shop replacement applications, this standalone fascia shell provides a clean foundation for professional refinishing and installation.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Before You Order

Please verify your vehicle year, trim configuration, front bumper design, and reference numbers before purchasing. Compare the bumper shape, grille and bezel openings, mounting points, and reference numbers with your existing part to confirm compatibility. Designed specifically for 2014–2016 Toyota Corolla L, LE & LE Eco pre-facelift models. Not intended for other bumper or trim configurations.

What’s Not Included

This listing includes the front bumper cover fascia shell only. Upper and lower grille components, side inserts or bezels, trim moldings, brackets, retainers, reinforcement components, lighting parts, and mounting hardware are not included unless specifically stated in the package contents.

Paint & Installation Notice

This bumper cover is supplied in a primed black, unpainted finish and requires surface preparation and professional painting before final installation. Professional test-fitting, paint preparation, color matching, and installation are recommended. Existing mounting hardware and surrounding bumper components should be inspected before installation and replaced when necessary.

Shipping & Packaging Note

Due to the size and flexible construction of automotive bumper covers, minor temporary flexing may occur during shipping. Allow the bumper cover to return to its natural shape at room temperature before test-fitting, preparation, and painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and Corolla® are registered trademarks of Toyota Motor Corporation. References to vehicle makes, models, trademarks, OEM numbers, Partslink numbers, interchange numbers, Hollander identifiers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, and existing part before purchase.