Honda

Product Overview

Restore the lower front-end appearance of your Honda CR-V with this aftermarket replacement Front Lower Bumper Cover Valance with Integrated Mesh Grille. This complete lower valance assembly includes a pre-assembled center honeycomb mesh grille and features a textured black matte finish for a clean, factory-style appearance. It is designed for North American 2017–2019 Honda CR-V models.

Package Includes

• 1× Front Lower Bumper Valance Skirt

• 1× Pre-assembled center honeycomb mesh grille air panel

• Textured black matte finish

• Partslink Number: HO1015117

• OEM Reference Number: 71102-TLA-A00

• Hollander Number: 101-60318

Lower Valance Assembly Only - This listing includes the Front Lower Bumper Valance Skirt with Pre-Assembled Center Honeycomb Mesh Grille ONLY.

The following components are not included:

• Front upper bumper bare-shell cover

• Upper chrome grille bars

• Fog-lamp housing caps

Existing factory components must be transferred from the original bumper assembly or purchased separately as needed.

Protective Shipping Notice

The integrated honeycomb mesh grille requires additional protection during transportation. This product is shipped in a full-size rigid protective case through FedEx Ground to help preserve the shape and structural integrity of the honeycomb grille and surrounding mounting areas.

Installation Notice

Professional installation is recommended. Inspect and test-fit the component before installation or modification. The textured black matte finish is typically installed without painting. Any optional refinishing or customization should be completed only after confirming proper fitment.

Compatibility Disclaimer

This is an aftermarket replacement part and is not a genuine Honda OEM product. OEM part numbers, North American interchange numbers, vehicle names, model names, and other reference identifiers are provided solely for product identification and compatibility-reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Product Overview

Built for 2022–2025 Toyota RAV4 Limited post-facelift models, this aftermarket front bumper cover features two pre-molded front parking radar sensor holes to match the corresponding premium-trim fascia configuration. The shell is formed from durable automotive-grade impact-resistant plastic and supplied in a primed black finish for professional prep and refinishing. Its sensor-ready layout makes it a practical replacement for front bumpers affected by collision damage, cracks, heavy scrapes, deformation, or prior repair work.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Radar & Fitment Check

This bumper cover is intended specifically for 2022–2025 Toyota RAV4 Limited post-facelift configurations with two pre-molded front parking radar sensor holes. Before ordering, compare the sensor-hole count and placement, grille openings, lower fascia profile, side openings, mounting locations, and reference numbers with your original bumper. Non-sensor or other trim-specific front fascia layouts may require a different cover.

Components Sold Separately

This listing includes the front bumper cover fascia shell only. Parking radar sensors, sensor brackets or retainers, grille components, side bezels or inserts, reinforcement parts, lighting components, emblems, mounting hardware, and other surrounding bumper accessories are not included unless specifically stated in the package contents.

Paint & Installation

The bumper cover is supplied in a primed black, unpainted finish and requires final surface preparation, color matching, and professional painting before installation. Test-fit the fascia before paintwork to verify sensor-hole positioning, grille alignment, and mounting-point fitment. Professional refinishing and installation are recommended for the best final result.

Packaging & Handling

Because front bumper covers are large, flexible exterior panels, minor temporary flexing may occur during packaging or transportation. After unpacking, allow the bumper cover to rest at room temperature and recover its natural contour before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, radar configuration, and existing components before purchase.

Product Overview

The rear bumper plays an important role in protecting your Honda HR-V while preserving its clean, modern crossover styling. If your original bumper has been damaged by a parking lot accident, a low-speed rear-end collision, loading cargo, or everyday driving, replacing the bumper cover is an effective way to restore your vehicle's exterior while maintaining its factory-inspired appearance. This 2019-2022 Honda HR-V Rear Bumper Cover features an OE-style design that follows the original body lines of compatible HR-V models. Finished with a smooth primed surface, it is ready for professional paint preparation and color matching. Once painted and installed, it helps restore the modern rear styling that makes the Honda HR-V one of today's most versatile compact crossover SUVs. Designed for collision repair, cosmetic restoration, and everyday vehicle maintenance, this replacement rear bumper cover provides a practical and cost-effective solution for replacing a cracked, scratched, or damaged rear bumper while maintaining the clean appearance of your HR-V.

Inspired by the Original HR-V Design

The Honda HR-V combines compact dimensions with SUV versatility, making it an excellent choice for urban driving and everyday adventures. This OE-style replacement rear bumper cover is designed to restore the original rear styling after accident damage or everyday wear, helping your HR-V retain its factory-inspired appearance.

Why Replace a Damaged Rear Bumper Cover?

The rear bumper is one of the most frequently damaged exterior components on a vehicle. Parking mishaps, low-speed impacts, loading cargo, and everyday driving can leave visible scratches, dents, cracks, or scuffs that affect your HR-V's overall appearance.

Replacing a damaged bumper cover can help:

• Restore your vehicle's original appearance

• Replace cracked or damaged bumper surfaces

• Improve overall exterior presentation

• Support rear-end collision repairs

• Complete cosmetic restoration projects

• Prepare your vehicle for resale or trade-in

For many vehicle owners, replacing a damaged bumper cover is often more practical and economical than repairing heavily damaged plastic components.

Primed Surface Ready for Paint

This bumper cover arrives with a smooth primed finish that simplifies the refinishing process.

Benefits include:

• Easier paint preparation

• Professional color matching

• Consistent surface quality

• Reduced preparation time before painting

• Smooth foundation for a factory-quality finish

Professional painting and color matching are recommended for the best appearance after installation.

Common Repair Applications

This rear bumper cover is commonly used for:

• Rear-end collision repair

• Parking damage restoration

• Cosmetic bumper replacement

• Insurance claim repairs

• Exterior body repair projects

• Daily driver maintenance

• Vehicle reconditioning before resale

Whether you're repairing collision damage or restoring your HR-V's appearance, this replacement rear bumper cover helps complete a professional-quality repair.

Product Features

• OE-style rear bumper cover replacement
• Precision-molded to complement factory body lines
• Durable automotive-grade construction
• Smooth primed finish ready for paint
• Ideal for collision repair and exterior restoration
• Helps restore original rear-end styling
• Suitable for professional body shop or DIY repair projects

Important Information

This listing includes one primed rear bumper cover only. Reflectors, parking sensors, mounting hardware, brackets, reinforcement components, trim pieces, and other accessories are sold separately unless otherwise specified.

FAQS

1. Does this rear bumper cover come painted?

No. This rear bumper cover is supplied in a smooth primed finish and must be professionally painted before installation to match your vehicle's color.

2. What is included with this bumper cover?

This listing includes one primed rear bumper cover only. Reflectors, parking sensors, mounting hardware, brackets, reinforcement bars, trim pieces, and other accessories are sold separately unless otherwise specified.

3. Is this an OEM Honda part?

No. This is an aftermarket replacement rear bumper cover designed for compatible Honda HR-V applications. It is manufactured to provide an OE-style appearance and fit.

4. Is professional installation recommended?

Yes. Professional installation is recommended to ensure proper alignment, paint preparation, and a factory-quality finish.

5. Is this bumper cover suitable for collision repair?

Yes. This bumper cover is commonly used for rear-end collision repairs, cosmetic restoration projects, insurance claim repairs, and everyday body repair work.

6. Can this bumper cover be painted to match my vehicle?

Yes. The primed surface is specifically designed for professional paint preparation and color matching to achieve a seamless factory-inspired appearance.

7. Will this rear bumper cover arrive folded?

Some bumper covers may be folded for shipping to reduce shipping costs. The bumper cover will typically return to its original shape after unpacking and standard installation procedures.

Compatibility Disclaimer

Honda® and HR-V® are registered trademarks of Honda Motor Co., Ltd. Velnox Auto is not affiliated with, endorsed by, sponsored by, or otherwise connected to Honda Motor Co., Ltd. Vehicle manufacturer names, model names, trim levels, and model years are used solely for product identification and compatibility purposes. This product is an aftermarket replacement part and is not manufactured, authorized, or approved by Honda Motor Co., Ltd.

Product Overview

The front bumper is one of the most noticeable exterior components of your Honda HR-V, helping protect your vehicle while enhancing its clean, modern appearance. If your original bumper has been damaged by a parking lot incident, road debris, or a minor collision, replacing the bumper cover is an effective way to restore your vehicle's exterior while maintaining its factory-inspired styling. This 2019-2022 Honda HR-V Front Bumper Cover features an OE-style design that follows the original body lines of compatible HR-V models. Finished with a smooth primed surface, it is ready for professional paint preparation and color matching. Once painted and installed, it helps restore the modern front-end styling that makes the Honda HR-V one of today's most versatile compact crossover SUVs. Designed for collision repair, cosmetic restoration, and everyday vehicle maintenance, this replacement front bumper cover provides a practical and cost-effective solution for replacing a cracked, scratched, or damaged bumper while preserving the clean appearance of your HR-V.

Inspired by the Original HR-V Design

The Honda HR-V combines compact dimensions with SUV versatility, making it an ideal choice for city driving and everyday adventures. This OE-style replacement front bumper cover is designed to restore the original front-end styling after accident damage or everyday wear, helping your HR-V maintain its factory-inspired appearance.

Why Replace a Damaged Front Bumper Cover?

The front bumper is one of the most exposed exterior components on any vehicle. Daily driving, parking, and road debris can result in scratches, dents, cracks, or other cosmetic damage that affects your HR-V's appearance.

Replacing a damaged bumper cover can help:

• Restore your vehicle's original appearance

• Replace cracked or damaged bumper surfaces

• Improve overall exterior presentation

• Support front-end collision repairs

• Complete cosmetic restoration projects

• Prepare your vehicle for resale or trade-in

For many vehicle owners, replacing a damaged bumper cover is often more practical and economical than repairing heavily damaged plastic components.

Primed Surface Ready for Paint

This bumper cover arrives with a smooth primed finish that simplifies the refinishing process.

Benefits include:

• Easier paint preparation

• Professional color matching

• Consistent surface quality

• Reduced preparation time before painting

• Smooth foundation for a factory-quality finish

Professional painting and color matching are recommended for the best appearance after installation.

Common Repair Applications

This front bumper cover is commonly used for:

• Front-end collision repair

• Accident damage restoration

• Cosmetic bumper replacement

• Insurance claim repairs

• Exterior body repair projects

• Daily driver maintenance

• Vehicle reconditioning before resale

Whether you're repairing collision damage or restoring your HR-V's appearance, this replacement bumper cover helps complete a professional-quality repair.

Product Features

• OE-style front bumper cover replacement
• Precision-molded to complement factory body lines
• Durable automotive-grade construction
• Smooth primed finish ready for paint
• Ideal for collision repair and exterior restoration
• Helps restore original front-end styling
• Suitable for professional body shop or DIY repair projects

Important Information

This listing includes one primed front bumper cover only. Grilles, emblems, fog lights, parking sensors, mounting hardware, brackets, reinforcement components, and other accessories are sold separately unless otherwise specified.

FAQS

1. Does this front bumper cover come painted?

No. This front bumper cover is supplied in a smooth primed finish and must be professionally painted before installation to match your vehicle's color.

2. What is included with this bumper cover?

This listing includes one primed front bumper cover only. Grilles, emblems, fog lights, parking sensors, mounting hardware, brackets, reinforcement bars, trim pieces, and other accessories are sold separately unless otherwise specified.

3. Is this an OEM Honda part?

No. This is an aftermarket replacement front bumper cover designed for compatible Honda HR-V applications. It is manufactured to provide an OE-style appearance and fit.

4. Is professional installation recommended?

Yes. Professional installation is recommended to ensure proper alignment, paint preparation, and a factory-quality finish.

5. Is this bumper cover suitable for collision repair?

Yes. This bumper cover is commonly used for front-end collision repairs, cosmetic restoration projects, insurance claim repairs, and everyday body repair work.

6. Can this bumper cover be painted to match my vehicle?

Yes. The primed surface is specifically designed for professional paint preparation and color matching to achieve a seamless factory-inspired appearance.

7. Will this front bumper cover arrive folded?

Some bumper covers may be folded for shipping to reduce shipping costs. The bumper cover will typically return to its original shape after unpacking and standard installation procedures.

Compatibility Disclaimer

Honda® and HR-V® are registered trademarks of Honda Motor Co., Ltd. Velnox Auto is not affiliated with, endorsed by, sponsored by, or otherwise connected to Honda Motor Co., Ltd. Vehicle manufacturer names, model names, trim levels, and model years are used solely for product identification and compatibility purposes. This product is an aftermarket replacement part and is not manufactured, authorized, or approved by Honda Motor Co., Ltd.

Product Overview

Restore a damaged rear end with this OE-style Rear Bumper Cover Fascia Bare Shell, designed as a standalone aftermarket replacement for post-facelift Honda Civic Sedan applications. Constructed from flexible automotive-grade plastic, the panel follows the original-style rear body contour and compatible mounting layout. It is supplied in a primed, unpainted finish for professional paint preparation and color matching.

Package Includes

This listing includes the rear bumper fascia main shell only.

The following components are NOT included:

• Continuous rear lower valance / lower lip

• Rear corner bezels or garnish pieces

• Reflectors or related lighting components

• Side retainers, brackets, clips, or installation hardware

• Additional rear bumper trim unless specifically stated

Compatible original components may be reused when applicable or replaced separately as needed.

Paint & Installation Notice

The bumper cover requires professional surface preparation, color matching, and final paint before installation. Always test fit before painting, drilling, cutting, or permanent modification to verify panel alignment and mounting points. Previous collision damage, worn retainers, damaged brackets, or distorted mounting areas may affect installation and should be inspected before fitting the replacement panel. Professional body-shop preparation and installation are recommended. Painted, installed, drilled, cut, damaged, or permanently modified products may not qualify for return under the VELNOX Auto Return Policy.

Folded Shipping & Unboxing Notice

Because of its flexible construction, the bumper cover may be professionally folded and securely packed inside a reinforced shipping carton to help reduce oversized-carrier shipping costs. Temporary bends, waves, creases, or packaging impressions may appear after unpacking and do not necessarily indicate permanent damage.

After unpacking:

1. Remove all protective packaging.

2. Place the bumper cover in a warm, clean area.

3. Allow sufficient time for the panel to recover its molded shape.

4. Apply low, controlled heat gradually and evenly only if necessary.

5. Confirm shape recovery before test fitting and paint preparation.

Avoid concentrated direct heat, open flame, or overheating, as excessive heat may damage the primer or permanently deform the panel.

Before Ordering

Compare Partslink HO1100311, OEM 04715-TBA-A10ZZ, the rear fascia design, and mounting locations with the original bumper before purchase. Confirm that the required lower valance, corner bezels, retainers, and related trim components are available for reuse or separate replacement.

Compatibility Disclaimer

This product is an aftermarket replacement and is not manufactured or supplied by Honda Motor Co., Ltd. OEM reference numbers, North American interchange numbers, vehicle names, trim names and body-style descriptions are provided solely for product identification and compatibility verification. Their use does not indicate that this product is a genuine Honda OEM part. Honda®, Civic® and related trademarks are the property of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by or authorized by Honda Motor Co., Ltd.

Product Overview

Restore the front end with this OE-style Front Bumper Cover Bare Shell, designed as an aftermarket replacement for compatible North American 2019–2021 Honda Civic Sedan and Coupe facelift models. Constructed from flexible automotive-grade plastic, the bumper cover follows the original-style body contour and mounting layout. It is supplied in a primed matte-black finish and requires professional preparation and painting before installation.

Package Includes

The following components are NOT included:

• Upper grille or chrome grille garnish

• Center lower honeycomb grille inserts

• Fog-light bezels or side bumper trim

• Fog lights, bulbs, wiring, or connectors

• Lower chin spoiler or splitter

• Front emblem or license-plate bracket

• Parking sensors or sensor brackets

• Impact absorber or reinforcement beam

• Side mounting brackets

• Clips, retainers, fasteners, or installation hardware

Compatible original components may be transferred from the existing bumper assembly when applicable.

Fitment & Ordering Notice

Designed for compatible North American 2019–2021 Honda Civic Sedan and Coupe facelift models using the matching bumper design.

Applicable body styles:

• Sedan — 4-Door

• Coupe — 2-Door

Applicable configurations may include LX, EX, EX-L, Sport, and Touring.

Does NOT fit:

• Hatchback models

• Type R models

• 2016–2018 pre-facelift models

Before ordering, verify the vehicle year, body style, trim configuration, bumper design, mounting locations, OEM 04711-TBA-A60ZZ, and Partslink HO1000314. Refer to the vehicle fitment chart for complete compatibility information.

Finish & Installation

The bumper cover is supplied primed and unpainted. Professional surface preparation may include cleaning, sanding, primer correction where needed, color matching, and final painting. Primer shade and appearance may vary slightly between production batches. Always test fit the bumper cover and transferred components before painting, drilling, cutting, or permanent modification. Professional installation is recommended. Previous collision damage, worn brackets, or misaligned mounting points may require repair or adjustment before installation. Painted, installed, drilled, cut, damaged, or permanently modified products may not qualify for return under the VELNOX Auto Return Policy.

Folded Shipping & Unboxing Notice

Due to its flexible construction, the bumper cover may be folded-packed inside a reinforced shipping carton to help reduce oversized shipping costs. Temporary bends, waves, or packaging impressions may appear after unpacking and do not necessarily indicate permanent damage.

After Unpacking

1. Remove all protective packaging.

2. Place the bumper cover in a warm, clean area.

3. Allow the panel time to recover its original shape.

4. Apply low, controlled heat gradually and evenly only if necessary.

5. Confirm proper shape and alignment before paint preparation.

Avoid concentrated or excessive heat, which may damage the primer or deform the panel.

Compatibility Disclaimer

This product is an aftermarket replacement component and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, model years, trim names, and body-style descriptions are provided solely for product identification and compatibility verification. Honda® and Civic® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Product Overview

Restore the rear-end appearance of your Honda Civic with this OE-style Rear Bumper Cover Fascia Bare Shell. Designed as a standalone replacement panel for collision repair or exterior restoration, this bumper cover follows the original-style shape and mounting layout for a clean replacement installation.

Package Includes

Product Features

• OE-style replacement rear bumper fascia

• Durable automotive-grade plastic construction

• Factory-style shape and mounting locations

• Suitable for collision repair and exterior restoration

• Designed for professional paint preparation and color matching

• Ideal replacement for cracked, dented, scratched, or damaged bumper covers

This listing is for the Rear Bumper Cover Bare Shell ONLY.

The following components are not included:

• Rear lower valance / diffuser trim

• Reflectors

• Bumper retainers or mounting hardware

• Additional rear bumper trim or accessories unless specifically stated

Compatible original components may be reused where applicable.

Paint & Installation Notice

The bumper cover is supplied primed and unpainted and requires paint preparation and color matching before final installation. Professional installation is recommended. Always test fit before painting to verify alignment and mounting points. Normal surface preparation may be required before painting. Existing mounting components or previously damaged areas may also require adjustment or replacement.

Important Ordering Notice

Before ordering, compare Partslink HO1100287, OEM 04715-TBA-A00ZZ, bumper design, and mounting locations with your original part. Only the component listed under Package Includes is included with your purchase.

Compatibility Disclaimer

This product is an aftermarket replacement component and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, trim names, and body-style descriptions are provided solely for product identification and compatibility verification. Honda® and Civic® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Product Overview

Restore a damaged front end with this OE-style Front Bumper Cover Fascia Bare Shell. Designed as a standalone replacement panel for collision repair or exterior restoration, this bumper cover follows the original-style shape and mounting layout for a clean replacement installation.

Package Includes

This listing is for the Front Bumper Cover Bare Shell ONLY.

The following components are not included:

• Front upper grille

• Fog light bezels / covers

• Additional trim or accessories unless specifically stated

Compatible original components may be reused where applicable.

Paint & Installation Notice

The bumper cover is supplied primed and unpainted and requires paint preparation and color matching before final installation. Professional installation is recommended. Always test fit before painting to verify alignment and mounting points. Existing mounting components or previously damaged areas may require adjustment or replacement.

Important Ordering Notice

Before ordering, compare Partslink HO1000302, OEM 04711-TGG-A00ZZ, bumper design, and mounting locations with your original part. Only the component listed under Package Includes is included with your purchase.

Compatibility Disclaimer

This product is an aftermarket replacement component and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, trim names, and body-style descriptions are provided solely for product identification and compatibility verification. Honda® and Civic® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Restore the clean, factory-style rear appearance of your Honda Accord with this replacement rear bumper cover fascia. Designed for the updated facelift rear-end layout, it is ideal for replacing a cracked, scraped, dented, or collision-damaged bumper cover.

Package Includes

• 1x Rear Bumper Cover Fascia Bare Shell

• Primed finish

• Interchange Number: HO1100318

• OEM Reference Number: 71501-TVA-A10ZZ

This listing includes the rear bumper cover bare shell only.

Lower valance or diffuser skirt, chrome exhaust outlet bezels, tailgate center license-plate garnish, rear reflector lamps, parking sensors, reinforcement components, retainers, brackets, and mounting hardware are not included. Compatible original components may need to be transferred from the existing bumper or purchased separately.

Important Compatibility Note

Designed for the 2021–2022 Honda Accord facelift rear bumper configuration. This part does not fit 2018–2020 pre-facelift models, which use a different bumper structure, exhaust-area layout, lower-valance mounting system, and surrounding trim configuration.

Paint and Installation Notice

The bumper cover is supplied with a primed finish and requires professional surface preparation and paint matching before installation. Test-fit the bumper and confirm all openings, mounting points, and trim connections before painting or modifying the part. Professional body-shop installation is strongly recommended. Minor primer variations or light handling marks may occur during manufacturing and shipping and are normally corrected during standard refinishing.

Compatibility Disclaimer

This product is an aftermarket replacement component and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, model names, trim names, and other identifiers are provided solely for product identification and compatibility-reference purposes. All reference numbers are intended to assist customers in verifying vehicle compatibility and selecting the correct replacement component before purchase. Honda® and Accord® are registered trademarks of Honda Motor Co., Ltd. Trim and configuration names are used solely to identify compatible vehicle applications. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Restore your Honda Accord’s clean, factory-style appearance with this replacement front bumper cover fascia. Designed for the updated facelift body layout, it is ideal for replacing a cracked, scraped, dented, or collision-damaged bumper cover. Its revised design features the wider center grille opening and streamlined side openings used on the facelift front fascia.

Package Includes

• 1x Front Bumper Cover Fascia Bare Shell

• North American Interchange Number: HO1000319

• OEM Reference Number: 71101-TVA-A50ZZ

• Hollander Reference Number: 105-10334

This listing includes the front bumper cover bare shell only.

Grilles, trim moldings, fog-light components, sensors, radar equipment, tow-hook cover, lower spoiler, reinforcement beam, absorber, retainers, brackets, splash shields, license-plate bracket, and mounting hardware are not included. Compatible original components may be transferred from the existing bumper when applicable.

Important Compatibility Note

Designed exclusively for the 2021–2022 facelift front bumper layout. This part does not fit 2018–2020 Honda Accord pre-facelift models, which use a different bumper shape, grille layout, mounting-tab pattern, inner support structure, and surrounding trim configuration.

Paint and Installation Notice

Professional test fitting, surface preparation, painting, and installation are strongly recommended. Confirm the bumper shape, openings, mounting points, and reference numbers before painting or modifying the part. Minor primer variations or light handling marks may occur during manufacturing and shipping and are normally corrected during standard body-shop preparation.

Compatibility Disclaimer

This product is an aftermarket replacement component and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, model names, and trim names are provided solely for product identification and compatibility-reference purposes. Honda® and Accord® are registered trademarks of Honda Motor Co., Ltd. Trim names are used only to identify compatible vehicle configurations. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Product Overview

Replace your damaged rear bumper with this Rear Bumper Cover Assembly for 2020–2022 Honda CR-V North American models. Featuring an integrated upper and lower shell, this assembly provides a complete replacement for the original bumper cover while maintaining the vehicle's original appearance. The upper bumper cover is supplied in a primed black finish for sanding, preparation, and painting, while the lower section features a textured black finish that closely matches the factory appearance. Combining both sections into a single assembly simplifies replacement and eliminates the need to purchase the upper and lower bumper covers separately.

Product Highlights

• Complete upper and lower integrated bumper cover assembly

• Primed upper bumper cover ready for paint

• Factory-style textured black lower section

• Designed for 2020–2022 Honda CR-V North American models

• Direct replacement for the original bumper cover assembly

Reference Numbers

What's Not Included

The following items are not included:

• Rear lower valance trim

• Rear bumper reflectors

• Mounting clips, screws, bolts, and other installation hardware

Fitment & Installation

Compatible with 2020–2022 Honda CR-V North American models.

• Supplied with a primed upper bumper cover that requires preparation and painting before installation.

• Test fit all components before painting or final installation.

• Professional installation is recommended.

Compatibility Disclaimer

This is an aftermarket replacement part and is not a genuine Honda OEM product. OEM part numbers, North American interchange numbers, vehicle names, and model names are provided solely for product identification and compatibility-reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, or endorsed by Honda Motor Co., Ltd.

Product Overview

Replace your original bumper cover with an OE-style aftermarket replacement engineered to match the factory design and fit of compatible 2020–2022 Honda CR-V models. Manufactured to follow the original body lines and mounting locations, this Front Upper Bumper Cover is an ideal solution for repairing collision damage, replacing a cracked bumper, or restoring the factory appearance of your vehicle. Manufactured using automotive-grade injection-molded thermoplastic, the bumper cover provides the flexibility and durability expected of modern exterior body components. It is supplied in a primed gray/black finish and is ready for final surface preparation and painting to match your vehicle. Before placing your order, compare your original bumper cover with the reference part numbers below to confirm compatibility.

Reference Part Numbers

• OEM: 04711-TLA-A50ZZ / 71101-TLA-A50ZZ / 04711-TNY-A00ZZ

• Partslink: HO1014106

• Hollander Number: 101-99430X

Package Includes

• 1 × Front Upper Bumper Cover Bare Shell

• Primed Gray/Black Finish

Items Not Included

This listing includes the Front Upper Bumper Cover Bare Shell only. The following original components are not included and should be reused from your existing bumper or purchased separately if replacement is required:

• Lower bumper valance

• Front grille and grille inserts

• Chrome moldings

• Fog light bezels

• Front emblem

• Parking sensors and sensor retainers (if equipped)

• Mounting brackets

• Clips, screws, fasteners, and installation hardware

• Any additional components not specifically listed

Fitment & Installation

This bumper cover is designed exclusively for the 2020–2022 Honda CR-V facelift models. It is not compatible with 2017–2019 models, as Honda redesigned the front bumper assembly, mounting locations, and trim configuration beginning with the 2020 model year. The bumper cover is supplied in a primed finish and must be painted before installation. We recommend performing a complete test fit before sanding, painting, drilling, or making any permanent modifications. Professional painting and installation are recommended to help ensure proper panel alignment, consistent body gaps, and accurate color matching. Products that have been painted, modified, or installed may not be eligible for return under the VELNOX Auto Return Policy.

Compatibility Disclaimer

This is an aftermarket replacement part and is not a genuine Honda OEM product. OEM part numbers, Partslink numbers, Hollander interchange numbers, vehicle names, model names, and other manufacturer references are provided solely for product identification and compatibility-reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd. The use of manufacturer names, trademarks, and reference numbers is for identification purposes only and does not imply any affiliation with or endorsement by the original vehicle manufacturer. Customers are responsible for verifying vehicle compatibility before purchase by reviewing the vehicle application, reference part numbers, and product specifications. If you have any questions regarding fitment, please contact VELNOX Auto before placing your order.

Product Overview

Restore the rear-end appearance of your Honda CR-V with this aftermarket replacement Rear Bumper Cover Fascia. This listing includes the rear bumper cover bare shell in a primed gray or black finish. Constructed from heavy-duty polypropylene plastic, the bumper cover requires professional surface preparation, color matching, and painting before installation.

Package Includes

• 1× Rear Bumper Cover Bare Shell

• Primed gray or black finish

• Partslink Number: HO1100301

• OEM Reference Numbers: 71501-TLA-A00 / 04712-TLY-A00ZZ / 04717-TLY-A00ZZ

• Hollander Number: 190-10142B

• Material: Heavy-Duty Polypropylene Plastic

This listing includes the Rear Bumper Cover Bare Shell ONLY.

The following components are not included:

• Lower valance lip skirt

• Side reflector lamps

• Chrome garnish strips

Existing factory components may need to be transferred from the original bumper assembly or purchased separately as needed.

Paint and Installation Notice

This rear bumper cover is supplied in a primed finish and is not pre-painted. Professional surface preparation, test fitting, color matching, painting, and installation are strongly recommended. Always test-fit the bumper cover before painting, drilling, trimming, or making any modifications. Painted, modified, or installed parts may not be eligible for return.

Compatibility Disclaimer

This is an aftermarket replacement part and is not a genuine Honda OEM product. OEM part numbers, North American interchange numbers, vehicle names, and model names are provided solely for product identification and compatibility reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, or endorsed by Honda Motor Co., Ltd.

Product Overview

Restore the front-end appearance of your vehicle with this Front Upper Bumper Cover Bare Shell. Designed as an OE-style aftermarket replacement for a cracked, dented, damaged, or missing original bumper cover, it follows the original body contours to help restore proper alignment and a clean, factory-inspired appearance. This bumper cover is intended for collision repair, exterior restoration, or replacement of the original front bumper cover on compatible North American-spec 2017–2019 Honda CR-V models.

For product identification and fitment verification, compare the following reference numbers with your original part before ordering:

• OEM Part Number Reference: 04711-TLA-A00ZZ

• North American Interchange Number: HO1000305

OEM and interchange numbers are provided for identification and compatibility-reference purposes only.

What Is Included

• 1 × Front Upper Bumper Cover Bare Shell Only

Brackets, retainers, mounting hardware, sensors, wiring, trim pieces, and other related components are also not included unless specifically stated. Compatible components may need to be transferred from the original bumper assembly or purchased separately. Please review the product images carefully to confirm the exact item included with this listing.

This listing is for the Front Upper Bumper Cover Bare Skin Shell ONLY. Lower bumper balance valance grille, chrome flying wing strip moldings, and fog light bezel covers are NOT included. 100% Fitment Guaranteed ONLY for North American 2017-2019 Pre-Facelift Models (LX, EX, EX-L, Touring). This lightweight flexible plastic bumper panel is folded-packed using high-resiliency security wraps to entirely bypass commercial oversized carrier freight surcharges, directly maximizing your dollar savings. Direct bolt-on replacement. 

Fitment Verification

This bumper cover is designed for compatible North American-spec 2017–2019 Honda CR-V models that match the vehicle configuration and reference numbers listed above. Fitment may vary based on trim level, production date, equipment package, bumper configuration, and previous vehicle modifications. Before ordering, verify the vehicle year, model, trim, original bumper design, OEM reference number, and interchange number.

Before painting or final installation, test-fit the bumper cover and confirm that:

• The mounting points align correctly

• The body contours match the vehicle

• All openings match the original bumper configuration

• Any original components being transferred fit correctly

Do not paint, drill, cut, permanently install, or otherwise modify the bumper cover until fitment has been fully confirmed. Products that have been painted, installed, damaged, or permanently modified may not be eligible for return under the VELNOX Auto Return Policy.

Paint and Installation Notice

This bumper cover is supplied with a primed surface and is not painted to match the vehicle’s exterior color. Test fitting, cleaning, sanding, surface preparation, additional priming, and professional color matching may be required before final painting and installation. As with most primed replacement body panels, standard body-shop preparation may be necessary to achieve the best finish and alignment. Professional painting and body-shop installation are strongly recommended to help ensure proper alignment, secure attachment, and an accurate color match.

FAQS

1. What exactly is included with this listing?

This listing includes one Front Upper Bumper Cover Bare Shell only. It is not a complete bumper assembly and does not include additional exterior components unless specifically stated.

2. Are the grille, fog lights, and emblem included?

No. The grille, fog lights, and emblem are not included. Compatible parts may need to be transferred from the original bumper assembly or purchased separately.

3. How can I confirm that this bumper cover fits my vehicle?

Confirm that your vehicle is a compatible North American-spec 2017–2019 Honda CR-V and compare your original part with:

• OEM Part Number Reference: 04711-TLA-A00ZZ

• North American Interchange Number: HO1000305

You should also verify the trim level, bumper openings, equipment package, and original bumper configuration before ordering.

4. Is the bumper cover already painted?

No. The bumper cover is supplied with a primed surface and requires preparation and painting before final installation. Professional color matching is recommended because paint appearance may vary due to vehicle age, fading, previous repairs, and production differences.

5. Should the bumper cover be test-fitted before painting?

Yes. Always test-fit the bumper cover before painting or making permanent modifications. Confirm the mounting points, openings, body contours, and compatibility of any transferred components before completing the repair.

This listing is for the Bumper Cover Bare Shell ONLY. Grille, fog lights, and emblem are NOT included. 100% Fitment Guaranteed for North American Models.

Compatibility Disclaimer

This is an aftermarket replacement part and is not a genuine Honda OEM product. OEM part numbers, interchange numbers, vehicle names, and model names are used solely for product identification and compatibility-reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, or endorsed by Honda Motor Co., Ltd.