Best Sellers

Product Description

This Front Bumper Bracket Right Passenger Side Support Retainer Mounting Spacer is designed for 2018-2020 Honda Accord (10th Gen Pre-Facelift Sedan All Trims Sport, EX, LX) and installs at the right-hand passenger-side front bumper and fender edge mounting area. This support guide retainer helps secure and position the front bumper cover along the passenger-side fender edge. It is suitable for replacing a bracket that is cracked, broken, loose, missing, or damaged during bumper removal, collision repair, or other front-end repair work. This listing includes the Right Passenger Side (RH) single component only – HO1043136 / OEM: 71193-TVA-A01 Core Spec.

Interchange Part Numbers

Please compare the component and reference numbers below with your existing part before ordering.

Key Features

• Right Passenger Side (RH) front bumper support retainer bracket

• Helps support and guide the bumper cover along the fender edge

• Integrated retention points for the corresponding side mounting location

• Suitable for replacing cracked, broken, loose, damaged, or missing retainers

• Useful for bumper replacement, collision repair, and front-end restoration

• Single-component replacement for the corresponding RH mounting position

Technical Fitment Notes

This front bumper support retainer guide bracket is intended specifically for the 2018-2020 pre-facelift 10th Gen Honda Accord configuration. The molded bracket profile, snap-in retention points, and mounting locations are designed to correspond with the right-hand passenger-side fender edge and front bumper corner mounting area, helping keep the bumper cover properly positioned and supported. Important: This component is intended for the 2018-2020 pre-facelift configuration and should not be treated as interchangeable with the 2021-2022 post-facelift configuration. The later models use a different fender-edge mounting and anchor layout. When matched to the correct vehicle application and mounting configuration, this bracket is designed as a direct replacement-style component without requiring cutting, drilling, or trimming.

Package Includes

• 1 × Front Bumper Right Passenger Side Support Retainer Mounting Spacer

Total: 1 Piece – Right Passenger Side (RH) Only

Important Component Notice

This listing includes only the component specifically stated in the Package Includes section. The left-side bracket and any additional hardware, fasteners, clips, screws, trim pieces, brackets, accessories, or surrounding components that are not specifically listed are not included. Product images may show surrounding vehicle components for installation reference or identification purposes only. Please review the product description and Package Includes section carefully before purchasing.

Before You Order

Please compare your original bracket, mounting points, part shape, and reference numbers with the information provided in this listing before purchase. This listing is for the Right Passenger Side (RH) component only. Please confirm the installation side, vehicle year, pre-facelift configuration, existing mounting layout, and reference numbers before ordering.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Honda Motor Co., Ltd. or American Honda Motor Co., Inc. Honda® and Accord® are trademarks or registered trademarks of their respective owners. References to vehicle makes, models, trim names, trademarks, OEM numbers, Partslink numbers, Hollander numbers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, production configuration, mounting points, installation side, and existing part before purchase. Please compare the listed reference numbers and original component carefully before ordering.

Product Overview

Restore major front-end components with this Front Bumper Structural Restoration Bundle Kit, designed as an OE-style aftermarket solution for collision repair and front-end rebuilding. The package combines the main bumper fascia with structural reinforcement, lower protection panels, mounting supports, license-plate bracket, and facelift-style fog-light bezels in one coordinated restoration bundle.

Package Includes

Product Highlights

• Comprehensive front-end collision restoration package

• Includes both exterior and structural bumper components

• OE-style contours and compatible mounting locations

• Heavy-duty steel bumper reinforcement beam

• Includes lower bumper and underbody protection panels

• Includes LH & RH bumper mounting supports

• Includes LH & RH facelift-style fog-light bezels

• Designed to simplify multi-component front-end repairs

Important Component Notice

This package includes only the components specifically listed in the Package Includes table. Items such as the upper grille assembly, center grille inserts, fog lamps, lighting wiring, emblem, sensors, absorber foam, and additional mounting hardware are not included unless specifically stated. Compatible original components may be transferred from the existing bumper assembly when applicable.

Paint & Installation Notice

The front bumper cover is supplied primed and unpainted and requires professional surface preparation, color matching, and final paint before installation. Always test fit the bumper cover and all related components before painting, drilling, cutting, or permanent modification. Because this package includes structural and underbody components, professional installation is strongly recommended. Previous collision damage, distorted mounting points, damaged brackets, or frame alignment issues should be inspected and corrected before installation. Painted, installed, drilled, cut, damaged, or permanently modified products may not qualify for return under the VELNOX Auto Return Policy.

Folded Shipping & Unboxing Notice

Due to the flexible construction of the bumper cover, the fascia may be professionally folded and securely packed inside a reinforced shipping carton to help reduce oversized-carrier shipping costs. Temporary bends, waves, creases, or packaging impressions may appear after unpacking and do not necessarily indicate permanent damage.

After unpacking:

1. Remove all protective packaging.

2. Place the bumper cover in a warm, clean area.

3. Allow sufficient time for the panel to recover its molded shape.

4. Apply low, controlled heat gradually and evenly only if necessary.

5. Confirm proper shape and alignment before paint preparation or installation.

Avoid concentrated direct heat, open flame, or overheating, as excessive heat may damage the primer or permanently deform the bumper cover.

Before Ordering

Compare the Partslink / interchange numbers, OEM reference numbers, component design, and mounting locations with the original vehicle components before purchase. Pay particular attention to the bumper cover design, fog-light bezel opening style, lower protection panels, and mounting support locations.

Compatibility Disclaimer

This product is an aftermarket replacement and appearance-upgrade component and is not manufactured or supplied by Honda Motor Co., Ltd. OEM reference numbers, North American interchange numbers, vehicle names, trim names and body-style descriptions are provided solely for identification and compatibility verification. Their use does not indicate that this product is a genuine Honda OEM part. Honda®, Civic® and related trademarks are the property of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by or authorized by Honda Motor Co., Ltd.

Product Overview

Restore a damaged rear bumper with this OE-style Rear Bumper Cover Fascia Bare Shell, designed as a direct aftermarket replacement for collision repair and exterior restoration. Constructed from durable, flexible automotive-grade plastic, this replacement bumper cover follows the original-style rear body contour and compatible factory-style mounting locations. It is supplied in a primed, unpainted finish and requires professional surface preparation, color matching, and final paint before installation.

Package Includes

Product Highlights

• OE-style rear bumper replacement design

• Durable automotive-grade plastic construction

• Factory-style contour and compatible mounting locations

• Primed surface ready for professional paint preparation

• Suitable for replacing cracked, dented, scratched, or collision-damaged bumper covers

• Designed for reuse of compatible original trim and surrounding components where applicable

This listing includes the rear bumper cover main shell ONLY.

The following components are NOT included:

• Rear lower diffuser / lower bumper lip

• Left and right rear side reflectors

• Mounting brackets, retainers, clips, or hardware

• Additional rear bumper trim or accessories unless specifically stated

Compatible original components may be transferred from the existing bumper assembly when applicable or purchased separately as needed.

Paint & Installation Notice

This bumper cover is supplied primed and unpainted and requires professional surface preparation, color matching, and painting before final installation. Always test fit the bumper cover before painting, drilling, cutting, or making permanent modifications to confirm panel alignment and mounting locations. Previous collision damage, worn retainers, damaged brackets, or misaligned mounting areas may affect installation and should be inspected before fitting the replacement bumper cover. Professional body-shop preparation and installation are recommended. Painted, installed, drilled, cut, damaged, or permanently modified products may not qualify for return under the VELNOX Auto Return Policy.

Folded Shipping & Unboxing Notice

Due to the flexible construction of the bumper cover, the panel may be professionally folded and securely packed inside a reinforced shipping carton to help reduce oversized-carrier shipping costs and improve shipping efficiency. Temporary bends, waves, creases, or packaging impressions may be visible immediately after unpacking. These conditions are commonly caused by folded packaging and do not necessarily indicate permanent damage to the bumper cover.

After unpacking:

1. Remove all protective wrapping and packaging materials.

2. Place the bumper cover in a warm, clean, flat area.

3. Allow sufficient time for the flexible plastic panel to recover toward its original molded shape.

4. If necessary, apply low, controlled heat gradually and evenly to affected areas.

5. Confirm the panel has recovered properly and test fit before paint preparation or installation.

Avoid concentrated direct heat, open flame, or overheating. Excessive heat may damage the primer, distort mounting areas, or permanently deform the bumper cover.

Before Ordering, please compare the following with your original bumper before purchase:

• Partslink No.: HO1100288

• OEM Reference No.: 04715-TBG-A00ZZ

• Original bumper design and mounting locations

Confirm that you are purchasing the Bare Shell ONLY configuration and that any required lower diffuser, reflectors, brackets, retainers, clips, or hardware are available for reuse or separate replacement.

FAQs

1. Is this rear bumper cover already painted?

No. It is supplied in a primed, unpainted finish and requires professional surface preparation, color matching, and final paint.

2. Are the lower diffuser and rear reflectors included?

No. This listing includes the rear bumper cover bare shell only. The lower diffuser / lip and left and right rear reflectors are not included.

3. Why may the bumper cover arrive folded?

The flexible bumper cover may be folded and securely protected inside a reinforced shipping carton to reduce oversized shipping costs. Temporary packaging impressions normally improve after proper unpacking and shape recovery.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured or supplied by Honda Motor Co., Ltd. OEM reference numbers, Partslink / North American interchange numbers, vehicle names, trim names, and body-style descriptions are provided solely for product identification and compatibility verification. Their use does not indicate that this product is a genuine Honda OEM part. Honda®, Civic®, and related trademarks are the property of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Product Overview

Restore a damaged rear end with this OE-style Rear Bumper Cover Fascia Bare Shell, designed as a standalone aftermarket replacement for compatible post-facelift Honda Civic Coupe applications using the matching Sport / Si-style rear fascia configuration. Constructed from flexible automotive-grade plastic, the panel follows the original-style rear body contour and compatible mounting layout.

Package Includes

This listing includes the rear bumper fascia main shell only.

The following components are NOT included:

• Center exhaust valance / diffuser

• Rear reflectors or related lighting components

• Side retainers, brackets, clips, or installation hardware

• Additional rear bumper trim unless specifically stated

Compatible original components may be reused when applicable.

Paint & Installation Notice

The bumper cover is supplied primed and unpainted and requires professional surface preparation, color matching, and final paint before installation. Always test fit before painting, drilling, cutting, or permanent modification to verify panel alignment and mounting points. Previous collision damage, worn retainers, damaged brackets, or distorted mounting areas may affect installation and should be inspected before fitting the replacement panel. Professional body-shop preparation and installation are recommended. Painted, installed, drilled, cut, damaged, or permanently modified products may not qualify for return under the VELNOX Auto Return Policy.

Folded Shipping & Unboxing Notice

Because of its flexible construction, the bumper cover may be professionally folded and securely packed inside a reinforced shipping carton to help reduce oversized-carrier shipping costs. Temporary bends, waves, creases, or packaging impressions may appear after unpacking and do not necessarily indicate permanent damage.

After unpacking:

1. Remove all protective packaging.

2. Place the bumper cover in a warm, clean area.

3. Allow sufficient time for the panel to recover its molded shape.

4. Apply low, controlled heat gradually and evenly only if necessary.

5. Confirm shape recovery before test fitting and paint preparation.

Avoid concentrated direct heat, open flame, or overheating, as excessive heat may damage the primer or permanently deform the panel.

Before Ordering

Compare Partslink HO1100312, OEM 04715-TBG-A00ZZ, the rear fascia design, and mounting locations with your original bumper before purchase. Confirm that any required center exhaust valance / diffuser and related trim components are available for reuse or separate replacement.

Compatibility Disclaimer

This product is an aftermarket replacement and restoration package and is not manufactured or supplied by Honda Motor Co., Ltd. OEM reference numbers, North American interchange numbers, vehicle names, trim names and body-style descriptions are provided solely for product identification and compatibility verification. Their use does not indicate that these products are genuine Honda OEM parts. Lighting installation requirements may vary depending on the vehicle’s original wiring, connectors and equipment configuration. Honda®, Civic® and related trademarks are the property of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by or authorized by Honda Motor Co., Ltd.

Product Overview

Restore a damaged front end with this OE-style Front Bumper Cover Fascia Bare Shell, designed as a standalone aftermarket replacement for collision repair and exterior restoration. Constructed from flexible automotive-grade plastic, this replacement panel follows the original-style front body contour and compatible factory-style mounting locations. It is supplied in a primed, unpainted finish for professional paint preparation and color matching.

Package Includes

Bare Shell ONLY – NOT Included

This listing includes the front bumper cover main shell only.

The following components are NOT included:

• Front upper grille or grille garnish

• Fog light bezels / side bumper trim

• Fog lights or related lighting components

• Lower grille / air-intake inserts

• Front emblem or license-plate bracket

• Mounting brackets, retainers, clips, or hardware

• Additional bumper trim or accessories unless specifically stated

Compatible original components may be transferred from the existing bumper assembly when applicable.

Paint & Installation Notice

The bumper cover requires surface preparation, color matching, and final paint before installation. Professional body-shop preparation and installation are recommended. Always test fit the bumper cover and transferred components before painting, drilling, cutting, or permanent modification to confirm alignment and mounting locations. Previous collision damage, worn brackets, damaged retainers, or misaligned mounting areas may require repair or adjustment before installation. Painted, installed, drilled, cut, damaged, or permanently modified products may not qualify for return under the VELNOX Auto Return Policy.

Folded Shipping & Unboxing Notice

Due to its flexible construction, the bumper cover may be professionally folded and securely packed inside a reinforced shipping carton to help reduce oversized-carrier shipping costs. Temporary bends, waves, creases, or packaging impressions may be visible after unpacking. These conditions can result from folded packaging and do not necessarily indicate permanent damage.

After unpacking:

1. Remove all protective packaging.

2. Place the bumper cover in a warm, clean area.

3. Allow the flexible panel sufficient time to recover its molded shape.

4. Apply low, controlled heat gradually and evenly only if necessary.

5. Confirm proper shape and alignment before paint preparation or installation.

Avoid concentrated direct heat, open flame, or overheating, as excessive heat may damage the primer or permanently deform the panel.

Before Ordering

Compare Partslink HO1000322, OEM 04711-TGG-A60ZZ, the original bumper design, and mounting locations before purchase. Confirm that any required grille, fog light bezels, trim, brackets, retainers, or hardware are available for reuse or separate replacement.

Compatibility Disclaimer

This is an aftermarket replacement and restoration package and is not manufactured or supplied by Honda Motor Co., Ltd. OEM reference numbers, North American interchange numbers, vehicle names, trim names and body-style descriptions are provided solely for identification and compatibility reference. Their use does not indicate that these products are genuine Honda OEM parts. Sensor, radar and lighting installation requirements may vary depending on the vehicle’s original wiring and equipment configuration. Buyers should verify compatibility before installation. Honda®, Civic® and related trademarks are the property of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by or authorized by Honda Motor Co., Ltd.

Product Overview

Restore the rear-end appearance of your Honda Civic with this complete 2-In-1 Rear Bumper Restoration Kit. This package combines the main rear bumper cover with the center lower lip / diffuser valance, giving you the two major exterior components needed for a cleaner and more complete rear bumper repair.

Package Includes

2-In-1 Kit Configuration

This restoration package includes:

1. Rear Bumper Cover Fascia Bare Shell

2. Rear Center Lower Lip / Diffuser Valance

The bumper cover and lower valance are supplied as separate components for installation.

Product Highlights

• Complete rear bumper cover and lower valance combination

• OE-style replacement design

• Primed bumper cover ready for professional paint preparation

• Matte black lower valance supplied in finished trim appearance

• Factory-style contours and mounting locations

• Suitable for collision repair and rear-end exterior restoration

• Convenient bundled solution compared with purchasing both components separately

Only the components specifically listed in the Package Includes table are supplied.

This kit does NOT include:

• Rear reflectors

• Side bumper retainers or brackets

• Mounting clips or hardware

• Additional rear bumper trim or accessories

Compatible original components may be reused where applicable.

Paint & Installation Notice

The rear bumper cover is supplied primed and unpainted and requires professional surface preparation, color matching, and painting before final installation. The lower valance is supplied in a matte black finish. Professional installation is recommended. Always test fit both components before painting the bumper cover to verify alignment and mounting points. Existing retainers, brackets, clips, or previously damaged mounting areas may require adjustment or replacement.

Important Ordering Notice

Before ordering, compare the reference numbers, component design, and mounting locations with your original parts.

Key references include:

• HO1100287 / OEM 04715-TBA-A00ZZ

• HO1116102 / OEM 71510-TBA-A00

• Hollander 106-05241 — Rear Bumper Cover

Only the two components listed in the package table are included.

Compatibility Disclaimer

This product is an aftermarket replacement and restoration package and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, trim names, and body-style descriptions are provided solely for product identification and compatibility verification. Custom lighting installation requirements may vary depending on the vehicle’s original wiring and equipment configuration. Honda® and Civic® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Product Overview

Restore the rear exterior of your Honda Accord with this coordinated facelift-style replacement kit. The package combines the main bumper cover with matching lower trim, chrome accents, exhaust outlet covers, and side mounting supports.

Package Includes

Important Package Details

This listing includes the Bright Chrome Silver exhaust outlet covers only.  Before ordering, compare your original bumper shape, lower valance design, exhaust openings, center garnish, side-retainer mounting points, and reference numbers with the components listed above.

Not Included

Rear reflector lamps, parking sensors, reinforcement beam, energy absorber, tailgate license-plate garnish, exhaust system components, wiring, mounting clips, hardware, and lower underbody support panels are not included.

Paint and Installation Notice

The rear bumper cover arrives primed and requires professional preparation and paint matching. Test-fit all components before painting, drilling, cutting, or final installation. Professional body-shop installation is strongly recommended. Minor primer variations or light handling marks may occur during manufacturing and shipping and are normally corrected during standard refinishing.

Compatibility Disclaimer

This product contains aftermarket replacement components and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, model names, trim names, and other identifiers are provided solely for product identification and compatibility-reference purposes. All reference numbers are intended to assist customers in verifying vehicle compatibility and selecting the correct replacement components before purchase. Honda® and Accord® are registered trademarks of Honda Motor Co., Ltd. Trim and configuration names are used solely to identify compatible vehicle applications. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Product Overview

Restore the complete front bumper assembly with this 2-piece Front Bumper Cover Kit for compatible 2020-2022 Honda CR-V models. The kit includes a replacement Front Upper Bumper Cover and a matching Front Lower Bumper Valance with a pre-installed center honeycomb mesh grille, providing a convenient solution for repairing or replacing damaged front bumper components. Both components are manufactured to OE-style specifications with factory mounting locations and body contours for a precise fit. The upper bumper cover is supplied in a primed gray/black finish and should be properly prepared and painted before installation. The lower valance features a durable textured matte black finish designed to closely match the original factory appearance. Purchasing both components together helps ensure a consistent fit and appearance while simplifying the repair process. Each kit is securely packaged in a reinforced oversized shipping carton with protective foam inserts to help minimize the risk of shipping damage.

Reference Numbers

What's Included

• Front Upper Bumper Cover

• Front Lower Bumper Valance

• Pre-installed Center Honeycomb Mesh Grille

What's Not Included

The following original vehicle components are not included and must be reused from your existing vehicle or purchased separately if required:

• Upper grille assembly

• Honda emblem

• Fog lamp bezels / covers

• Parking sensors and sensor retainers (if equipped)

• Front bumper reinforcement

• Energy absorber

• Tow hook cover

• Mounting brackets

• Clips, screws, retainers, and other installation hardware

• Any components not specifically listed above

Fitment & Installation

Compatible with North American 2020–2022 Honda CR-V Facelift LX and EX models equipped with the corresponding factory front bumper configuration. This kit is not compatible with 2017–2019 Honda CR-V models due to differences in bumper design, lower valance, and mounting configuration. Before ordering, compare your original part numbers with the reference information above to verify compatibility.Test fit all components before painting or final installation. Professional installation is recommended to ensure proper alignment with adjacent body panels. Products that have been painted, modified, or installed may not qualify for return under the VELNOX Auto Return Policy.

Compatibility Notice

This is an aftermarket replacement product and is not a genuine Honda OEM part. OEM part numbers, Partslink numbers, Hollander interchange numbers, vehicle names, model names, and other manufacturer references are provided solely for product identification and compatibility reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd. References to Honda®, CR-V®, OEM part numbers, and interchange numbers are used only to identify the intended vehicle application and do not imply any affiliation with or endorsement by the original vehicle manufacturer. Vehicle production dates, trim levels, and factory-installed equipment may affect compatibility. Please verify fitment before placing your order. If you have any questions regarding compatibility, please contact VELNOX Auto before ordering.

Product Overview

This Front Lower Bumper Valance features a factory-style integrated center honeycomb mesh grille and is manufactured to replace the original lower bumper valance on compatible 2020–2022 Honda CR-V models. The factory-style profile, mounting locations, and textured finish help maintain the original appearance of the front bumper after repair or replacement. Injection molded from automotive-grade thermoplastic, the valance is built to withstand everyday road conditions while maintaining the flexibility expected of modern bumper components. The integrated mesh grille comes pre-installed, eliminating the need for separate assembly and simplifying installation. Finished in textured matte black, the valance is designed to closely match the original factory surface and typically does not require painting before installation.

Part Information

• OEM Part Numbers： 71102-TLA-A50 | 71102-TLA-A70

• Partslink Number：HO1015122

• Hollander Interchange Number:101-99430X

What's Included

• Front Lower Bumper Valance Skirt

• Pre-installed Center Honeycomb Mesh Grille

• Textured Matte Black Finish

The following original components are not included:

• Upper bumper cover

• Upper grille assembly

• Front emblem

• Headlight eyebrow trim

• Fog lamp housing caps / bezels

• Parking sensors and retainers (if equipped)

• Mounting brackets

• Clips, screws, fasteners, and other installation hardware

• Any components not specifically listed above

Original components may be reused if they remain in good condition.

Fitment & Installation

Compatible with North American 2020–2022 Honda CR-V facelift models only. This valance is not compatible with 2017–2019 models, as Honda introduced a revised front bumper assembly and lower grille design beginning with the 2020 facelift. Before ordering, compare your original part with the OEM, Partslink, or Hollander reference numbers provided above. For best results, test fit the part before making any permanent modifications. Professional installation is recommended to ensure proper alignment with the original bumper assembly. Products that have been painted, modified, or installed may not qualify for return under the VELNOX Auto Return Policy.

Compatibility Disclaimer

This is an aftermarket replacement part and is not a genuine Honda OEM product. OEM part numbers, Partslink numbers, Hollander interchange numbers, vehicle names, model names, and other manufacturer references are provided solely for product identification and compatibility reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd. References to Honda®, CR-V®, OEM part numbers, and interchange numbers are used only to identify the intended vehicle application and do not imply any relationship with or approval by Honda Motor Co., Ltd. Vehicle production dates, trim levels, and factory-installed equipment may affect compatibility. Please verify fitment before placing your order or contact VELNOX Auto if you need assistance.

Product Overview

Restore the front-end appearance of your Honda CR-V with this aftermarket replacement Front Upper Bumper Cover Fascia. Designed for North American 2017–2019 Honda CR-V pre-facelift models, this replacement panel features an OE-style shape and a lightweight, flexible plastic construction. The bumper cover is supplied in a primed gray or black finish. Professional surface preparation, test fitting, color matching, painting, and installation are required.

Package Includes

• 1× Front Bumper Upper Cover Bare Skin Shell Panel

• Primed gray or black finish

• Pre-facelift specifications

• Partslink Number: HO1014104

• OEM Reference Numbers: 04711-TLA-A00ZZ / 71101-TLA-A00ZZ

• Hollander Number: 101-60317

Bare Shell Only

This listing includes the Front Upper Bumper Cover Bare Skin Shell ONLY.

The following components are not included:

• Lower bumper balance or valance grille

• Chrome flying-wing strip moldings

• Fog-light bezel covers

Existing factory components must be transferred from the original bumper cover or purchased separately as needed.

Folded Packaging Notice

To reduce oversized carrier shipping surcharges and provide greater shipping savings, this flexible bumper cover may be securely folded and packed with high-resiliency protective wrapping. Temporary bends, creases, or deformation may be visible after unpacking. Place the bumper cover in a warm environment and allow it sufficient time to gradually return to its original shape before test fitting or installation. Controlled heat may also be applied carefully by a qualified professional when necessary.

Paint and Installation Notice

This bumper cover is supplied in a primed finish and is not pre-painted. Professional surface preparation, test fitting, color matching, painting, and installation are strongly recommended. Always test-fit the bumper cover before painting, drilling, trimming, or making any modifications. Painted, modified, or installed parts may not be eligible for return.

Compatibility Disclaimer

This product contains aftermarket replacement components and is not a genuine Honda OEM assembly. OEM reference numbers, North American interchange numbers, vehicle names, model names, trim names, and other reference identifiers are provided solely for product identification and compatibility-reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Product Overview

Restore the lower front-end appearance of your Honda CR-V with this aftermarket replacement Front Lower Bumper Cover Valance with Integrated Mesh Grille. This complete lower valance assembly includes a pre-assembled center honeycomb mesh grille and features a textured black matte finish for a clean, factory-style appearance. It is designed for North American 2017–2019 Honda CR-V models.

Package Includes

• 1× Front Lower Bumper Valance Skirt

• 1× Pre-assembled center honeycomb mesh grille air panel

• Textured black matte finish

• Partslink Number: HO1015117

• OEM Reference Number: 71102-TLA-A00

• Hollander Number: 101-60318

Lower Valance Assembly Only - This listing includes the Front Lower Bumper Valance Skirt with Pre-Assembled Center Honeycomb Mesh Grille ONLY.

The following components are not included:

• Front upper bumper bare-shell cover

• Upper chrome grille bars

• Fog-lamp housing caps

Existing factory components must be transferred from the original bumper assembly or purchased separately as needed.

Protective Shipping Notice

The integrated honeycomb mesh grille requires additional protection during transportation. This product is shipped in a full-size rigid protective case through FedEx Ground to help preserve the shape and structural integrity of the honeycomb grille and surrounding mounting areas.

Installation Notice

Professional installation is recommended. Inspect and test-fit the component before installation or modification. The textured black matte finish is typically installed without painting. Any optional refinishing or customization should be completed only after confirming proper fitment.

Compatibility Disclaimer

This is an aftermarket replacement part and is not a genuine Honda OEM product. OEM part numbers, North American interchange numbers, vehicle names, model names, and other reference identifiers are provided solely for product identification and compatibility-reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.