Best Sellers

Product Overview

This aftermarket rear bumper cover is designed for 2014–2016 Nissan Rogue S & SV pre-facelift models using the corresponding non-sensor one-piece rear fascia configuration. Unlike a separate upper bumper and lower valance setup, this version is manufactured as a single unified rear bumper assembly, combining the upper body-panel section and lower valance-style area into one integrated shell. The one-piece construction helps maintain the correct factory-style rear profile while simplifying replacement of a damaged original fascia. Made from durable automotive-grade impact-resistant plastic, the bumper cover is suitable for collision repair, cosmetic restoration, or replacement of panels affected by cracks, scrapes, deformation, or previous repair work.

Reference Numbers

Package Includes

• 1x Complete Rear Bumper Cover Unified Assembly

• Integrated upper body-panel and lower valance-style fascia design

• Single-piece construction

One-Piece Configuration

This product is supplied as one complete molded rear bumper cover, not as two separate bumper pieces. The upper bumper section and lower black valance-style area are incorporated into the same unified fascia structure for the corresponding 2014–2016 Nissan Rogue S & SV pre-facelift configuration. Before ordering, compare the overall rear bumper contour, lower fascia design, reflector areas, mounting locations, and reference numbers with your existing part.

Fitment Notes

Designed for 2014–2016 Nissan Rogue S & SV pre-facelift models using the compatible non-sensor rear bumper layout. Sensor-equipped, higher-trim, or differently configured Rogue rear bumpers may use another fascia design. Verify your vehicle’s trim and existing bumper layout before purchase.

What’s Not Included

This listing includes the complete one-piece rear bumper cover assembly only. Reflectors, parking sensors, reinforcement bars, impact absorbers, brackets, retainers, mounting hardware, lighting components, and other surrounding rear bumper parts are not included unless specifically stated in the package contents.

Finish & Installation

The bumper cover should be test-fitted before final refinishing or installation to confirm alignment with the quarter-panel edges, reflector locations, and mounting points. Professional body-shop preparation and installation are recommended, particularly when the vehicle has previous collision damage or damaged surrounding mounting components.

Packaging & Handling

As a large flexible exterior body panel, the bumper cover may experience minor temporary flexing during packaging or transportation. After unpacking, allow the fascia to rest at room temperature and recover its natural contour before test-fitting or installation.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Nissan Motor Co., Ltd. Nissan® and Rogue® are registered trademarks of Nissan Motor Co., Ltd. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, rear bumper configuration, and existing components before purchase.

Product Overview

Designed for 2014–2016 Nissan Rogue Premium, Luxury & SL pre-facelift models, this front bumper cover is configured for vehicles equipped with pre-molded front parking radar sensor openings. Rather than using the plain non-sensor fascia found on lower trims, this version follows the higher-trim sensor-ready bumper layout, making it a more appropriate replacement when restoring a damaged premium-spec front end. The cover is made from durable automotive-grade impact-resistant plastic and supplied in a primed finish for professional preparation and repainting.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face / Fascia Shell

Sensor-Ready Fitment

This bumper cover is intended for 2014–2016 Nissan Rogue Premium, Luxury & SL trims with the corresponding front parking radar sensor-hole layout. Before ordering, compare the sensor-hole positions, grille opening, lower fascia shape, side openings, mounting tabs, and reference numbers with the bumper currently on the vehicle. The standard S/SV non-sensor fascia uses a different configuration.

What’s Not Included

Only the front bumper cover shell is included. Parking radar sensors, sensor holders or brackets, grille assemblies, side bezels, reinforcement components, lighting parts, emblems, retainers, and installation hardware are not included unless specifically listed in the package contents.

Refinishing & Installation

The bumper cover is supplied in a primed, unpainted finish intended for professional refinishing. Test-fit the fascia before painting, paying particular attention to the sensor openings, grille alignment, fender edges, and mounting locations. Final surface preparation, color matching, painting, and professional installation are recommended.

Packaging Note

The flexible construction of an automotive bumper cover may allow minor temporary movement in shape during shipping. After unpacking, allow the fascia to rest at room temperature and return to its natural contour before fitment checks or paint preparation.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Nissan Motor Co., Ltd. Nissan® and Rogue® are registered trademarks of Nissan Motor Co., Ltd. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

This aftermarket front bumper cover is designed for 2014–2016 Nissan Rogue S & SV pre-facelift models, using the non-sensor smooth short-grille front fascia configuration. The bumper cover is molded from durable automotive-grade impact-resistant plastic and supplied in a primed black finish for professional preparation and color matching. Its cleaner short-grille layout is intended to match the corresponding standard-trim Rogue front-end design, making it a practical replacement for bumpers damaged by collisions, cracks, deep scrapes, deformation, or previous repair work.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face / Fascia Shell

Front Fascia Configuration

This bumper cover is intended specifically for 2014–2016 Nissan Rogue S & SV pre-facelift models with the non-sensor smooth short-grille layout. Before ordering, compare the original bumper’s grille opening shape, sensor-hole configuration, side openings, mounting tabs, and overall fascia profile. Rogue bumper designs can vary by trim and equipment package, so the visual layout should match before purchase.

What Is Not Included

This listing includes the front bumper cover shell only. Upper or lower grille components, side inserts or bezels, brackets, retainers, reinforcement parts, lighting components, sensors, emblems, and mounting hardware are not included unless specifically identified in the package contents.

Paint & Body-Shop Preparation

The bumper cover arrives in a primed black, unpainted finish and requires final preparation and painting before installation. Test-fit the fascia prior to paintwork to confirm alignment around the grille opening, fenders, headlights, and mounting locations. Professional surface preparation, color matching, refinishing, and installation are recommended.

Shipping & Shape Recovery

Front bumper covers are flexible exterior body panels and may experience minor temporary flexing during packaging or transit. After unpacking, allow the fascia to rest at room temperature and recover its normal contour before test-fitting or beginning paint preparation.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Nissan Motor Co., Ltd. Nissan® and Rogue® are registered trademarks of Nissan Motor Co., Ltd. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, front fascia configuration, and existing components before purchase.

Product Description

This Front Bumper Cover Replacement is designed for 2016-2019 Nissan Sentra SL, Nismo, and Premium Trims Only with the 7th Gen post-facelift front-end configuration and pre-molded front parking radar sensor holes. The bumper cover serves as the exterior front fascia shell and is suitable for replacing a cracked, scraped, dented, deformed, or collision-damaged original front bumper cover. Its molded profile is designed to correspond with the specified post-facelift front-end contours while retaining the required sensor-hole configuration. This listing includes the standalone front bumper cover shell only – NI1000315 / OEM: 62022-4FU1H, finished in primed black.

Interchange Part Numbers

Please compare your vehicle trim, front bumper configuration, sensor layout, and reference numbers with the information below before ordering.

Key Features

• Standalone 1-piece front bumper cover replacement shell

• Designed for 2016-2019 Nissan Sentra SL, Nismo, and Premium trims

• 7th Gen post-facelift front fascia configuration

• Pre-molded front parking radar sensor holes

• Primed black surface ready for proper paint preparation and refinishing

• Molded profile for the corresponding front fascia and mounting layout

• Suitable for collision repair, exterior restoration, and damaged bumper replacement

Technical Fitment Notes

This front bumper cover is intended specifically for the 2016-2019 Nissan Sentra 7th Gen post-facelift SL, Nismo, and Premium configuration. The molded fascia profile incorporates pre-molded front parking radar sensor holes as part of the bumper shell design. These openings are an important configuration detail when comparing this replacement with the existing front bumper cover. Important: This bumper cover is intended for vehicles equipped with the corresponding front parking radar sensor hole configuration. It should not be treated as interchangeable with a smooth non-sensor bumper cover or another fascia configuration that uses a different sensor-hole or mounting layout. When matched to the correct vehicle, trim, and bumper configuration, this cover is designed as a direct replacement-style exterior body component for the corresponding mounting locations.

Package Includes

• 1 × Front Bumper Cover Face Shell

Total: 1 Piece – Standalone Front Bumper Cover Shell Only

Important Component Notice

This listing includes only the front bumper cover shell specifically stated in the Package Includes section. Parking radar sensors, sensor hardware, grilles, grille inserts, trim pieces, emblems, brackets, retainers, absorber components, reinforcement bars, fog light components, fasteners, clips, and other surrounding parts are not included unless specifically stated otherwise. The bumper cover includes the described pre-molded sensor holes only. Electronic sensors and related hardware are not included. Product images may show surrounding vehicle components for installation reference or identification purposes only. Please review the Product Description and Package Includes section carefully before purchasing.

Before You Order

Please compare your original front bumper cover, vehicle trim, front fascia configuration, parking sensor layout, mounting points, part shape, and reference numbers with the information provided in this listing before purchase. This listing is for the 2016-2019 Nissan Sentra SL, Nismo, and Premium 7th Gen post-facelift configuration with pre-molded front parking radar sensor holes. Please confirm these features and the listed interchange numbers before ordering.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Nissan Motor Co., Ltd. or Nissan North America, Inc. Nissan® and Sentra® are trademarks or registered trademarks of their respective owners. References to vehicle makes, models, trim names, trademarks, OEM numbers, Partslink numbers, Hollander numbers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, production configuration, sensor configuration, mounting points, and existing part before purchase. Please compare the listed reference numbers and original component carefully before ordering.

Product Description

This Front Bumper Cover Replacement is designed for 2016-2019 Nissan Sentra Standard Base S and SV Trims Only with the 7th Gen post-facelift front-end configuration and smooth non-sensor V-Motion grille layout. The bumper cover serves as the exterior front fascia shell and is suitable for replacing a cracked, scraped, dented, deformed, or collision-damaged original front bumper cover. Its molded profile is designed to correspond with the specified post-facelift grille opening, front fascia contours, and surrounding mounting areas. This listing includes the standalone front bumper cover shell only – NI1000314 / OEM: 62022-4FU0H Core Spec, finished in primed black.

Interchange Part Numbers

Please compare your vehicle trim, front bumper configuration, sensor layout, and reference numbers with the information below before ordering.

Key Features

• Standalone 1-piece front bumper cover replacement shell

• Designed for 2016-2019 Nissan Sentra Base S and SV trims

• 7th Gen post-facelift front fascia configuration

• Smooth non-sensor bumper layout

• V-Motion grille front-end configuration

• Primed black surface ready for proper paint preparation and refinishing

• Suitable for collision repair, exterior restoration, and damaged bumper replacement

Technical Fitment Notes

This front bumper cover is intended specifically for the 2016-2019 Nissan Sentra 7th Gen post-facelift configuration. The molded fascia profile is designed around the corresponding post-facelift front-end layout, including the V-Motion grille opening, front corner contours, lower fascia structure, and mounting locations. Important: This bumper cover is intended for the smooth non-sensor configuration. It should not be treated as interchangeable with bumper covers that use factory-molded parking sensor openings or another front fascia configuration with different openings or mounting layouts. When matched to the correct vehicle, trim, and bumper configuration, this cover is designed as a direct replacement-style exterior body component for the corresponding mounting locations.

Package Includes

• 1 × Front Bumper Cover Face Shell

Total: 1 Piece – Standalone Front Bumper Cover Shell Only

Important Component Notice

This listing includes only the front bumper cover shell specifically stated in the Package Includes section. Grilles, grille inserts, trim pieces, emblems, parking sensors, sensor hardware, brackets, retainers, absorber components, reinforcement bars, fog light components, fasteners, clips, and other surrounding parts are not included unless specifically stated otherwise. Product images may show surrounding vehicle components for installation reference or identification purposes only. Please review the Product Description and Package Includes section carefully before purchasing.

Before You Order

Please compare your original front bumper cover, vehicle trim, front fascia configuration, sensor layout, mounting points, part shape, and reference numbers with the information provided in this listing before purchase. This listing is for the 2016-2019 Nissan Sentra Standard Base S and SV 7th Gen post-facelift smooth non-sensor configuration. Please confirm your vehicle trim, existing bumper layout, and listed interchange numbers before ordering.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Nissan Motor Co., Ltd. or Nissan North America, Inc. Nissan® and Sentra® are trademarks or registered trademarks of their respective owners. References to vehicle makes, models, trim names, trademarks, OEM numbers, Partslink numbers, Hollander numbers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, production configuration, sensor configuration, mounting points, and existing part before purchase. Please compare the listed reference numbers and original component carefully before ordering.

Product Description

This Rear Bumper Cover Lower Replacement is designed for 2019-2022 Nissan Altima Limited, SL, and Platinum Trims Only with the 6th Gen pre-facelift rear-end configuration and pre-molded 4 backup radar sensor holes. This lower rear bumper cover helps restore the exterior lower fascia area after cracking, impact damage, deformation, scraping, or collision repair. Its molded profile is designed to correspond with the specified rear bumper configuration while retaining the required sensor-hole layout. This listing includes the standalone rear lower bumper cover only – NI1100312 / OEM: 85022-6MA5H, finished in automotive-grade black.

Interchange Part Numbers

Please compare your vehicle trim, rear bumper configuration, sensor layout, and reference numbers with the information below before ordering.

Key Features

• Standalone rear lower bumper cover replacement

• Designed for 2019-2022 Nissan Altima Limited, SL, and Platinum trims

• 6th Gen pre-facelift rear fascia configuration

• Pre-molded with 4 backup radar sensor holes

• Automotive-grade black finish

• Molded profile for the corresponding rear bumper and lower fascia layout

• Suitable for collision repair, exterior restoration, and damaged lower bumper replacement

Technical Fitment Notes

This rear lower bumper cover is intended specifically for the 2019-2022 Nissan Altima 6th Gen pre-facelift Limited, SL, and Platinum configuration. The molded lower fascia profile incorporates 4 pre-molded backup radar sensor holes as part of the bumper design. These openings are an important configuration detail when comparing this replacement with the existing rear bumper component. Important: This component is intended for vehicles equipped with the corresponding 4 backup radar sensor hole configuration. It should not be treated as interchangeable with a smooth non-sensor lower bumper cover or another rear fascia configuration that uses a different sensor-hole or mounting layout. When matched to the correct vehicle and bumper configuration, this lower cover is designed as a direct replacement-style exterior body component for the corresponding mounting locations.

Package Includes

• 1 × Rear Bumper Cover Lower

Total: 1 Piece – Standalone Rear Lower Bumper Cover Only

Important Component Notice

This listing includes only the rear lower bumper cover specifically stated in the Package Includes section. Backup radar sensors, sensor hardware, upper bumper cover, trim pieces, reflectors, brackets, retainers, absorber components, reinforcement bars, exhaust trim components, fasteners, clips, and other surrounding parts are not included unless specifically stated otherwise. The component includes the described pre-molded 4 backup radar sensor holes only. Electronic sensors and related hardware are not included. Product images may show surrounding vehicle components for installation reference or identification purposes only. Please review the Product Description and Package Includes section carefully before purchasing.

Before You Order

Please compare your original rear bumper component, vehicle trim, fascia configuration, sensor-hole layout, mounting points, part shape, and reference numbers with the information provided in this listing before purchase. This listing is for the 2019-2022 Nissan Altima Limited, SL, and Platinum 6th Gen pre-facelift configuration with 4 backup radar sensor holes. Please confirm these features and the listed interchange numbers before ordering.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Nissan Motor Co., Ltd. or Nissan North America, Inc. Nissan® and Altima® are trademarks or registered trademarks of their respective owners. References to vehicle makes, models, trim names, trademarks, OEM numbers, Partslink numbers, Hollander numbers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, production configuration, sensor configuration, mounting points, and existing part before purchase. Please compare the listed reference numbers and original component carefully before ordering.

Product Description

This Rear Bumper Cover Replacement is designed for 2019-2022 Nissan Altima Standard S, SR, and SV Trims Only with the 6th Gen pre-facelift rear-end configuration and flush smooth non-sensor slim-reflector pocket layout. The bumper cover serves as the exterior rear fascia shell and is suitable for replacing a cracked, scraped, dented, deformed, or collision-damaged original rear bumper cover. Its molded profile is designed to correspond with the specified pre-facelift rear-body contours, reflector pocket areas, and surrounding mounting locations. This listing includes the standalone rear bumper cover shell only – NI1100311 / OEM: 85022-6CA0H Core Spec.

Interchange Part Numbers

Please compare your vehicle trim, rear bumper configuration, sensor layout, and reference numbers with the information below before ordering.

Key Features

• Standalone 1-piece rear bumper cover replacement shell

• Designed for 2019-2022 Nissan Altima S, SR, and SV trims

• 6th Gen pre-facelift rear fascia configuration

• Flush smooth non-sensor bumper layout

• Slim-reflector pocket configuration

• Molded profile for the corresponding rear-body and mounting layout

• Suitable for collision repair, exterior restoration, and damaged bumper replacement

Technical Fitment Notes

This rear bumper cover is intended specifically for the 2019-2022 Nissan Altima 6th Gen pre-facelift configuration. The molded fascia profile is designed around the corresponding rear-end layout, including the outer corner contours, slim-reflector pocket areas, lower fascia structure, and mounting locations. Important: This bumper cover is intended for the flush smooth non-sensor configuration. It should not be treated as interchangeable with rear bumper covers that use factory-molded parking sensor openings or another rear fascia configuration with different openings or mounting points. When matched to the correct vehicle and bumper configuration, this cover is designed as a direct replacement-style exterior body component for the corresponding mounting locations.

Package Includes

• 1 × Rear Bumper Cover Face Shell

Total: 1 Piece – Standalone Rear Bumper Cover Shell Only

Important Component Notice

This listing includes only the rear bumper cover shell specifically stated in the Package Includes section. Reflectors, parking sensors, sensor hardware, trim pieces, brackets, retainers, absorber components, reinforcement bars, exhaust trim components, fasteners, clips, and other surrounding parts are not included unless specifically stated otherwise. Product images may show surrounding vehicle components for installation reference or identification purposes only. Please review the Product Description and Package Includes section carefully before purchasing.

Before You Order

Please compare your original rear bumper cover, vehicle trim, fascia configuration, sensor layout, reflector pocket layout, mounting points, part shape, and reference numbers with the information provided in this listing before purchase. This listing is for the 2019-2022 Nissan Altima Standard S, SR, and SV 6th Gen pre-facelift smooth non-sensor configuration. Please confirm your vehicle trim, existing bumper layout, and listed interchange numbers before ordering.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Nissan Motor Co., Ltd. or Nissan North America, Inc. Nissan® and Altima® are trademarks or registered trademarks of their respective owners. References to vehicle makes, models, trim names, trademarks, OEM numbers, Partslink numbers, Hollander numbers, and other cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for verifying compatibility with their specific vehicle, trim level, production configuration, sensor configuration, reflector configuration, mounting points, and existing part before purchase. Please compare the listed reference numbers and original component carefully before ordering.

Product Overview

Designed for 2022–2025 Toyota RAV4 Limited post-facelift models, this aftermarket rear bumper cover features four pre-molded backup radar sensor holes to match the corresponding flagship rear fascia configuration. Manufactured from durable automotive-grade impact-resistant plastic, the bumper cover is supplied in a black finish and provides a direct replacement solution for rear fascia panels affected by collision damage, cracks, deep scrapes, deformation, or previous repair work.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Sensor & Application Verification

This bumper cover is intended specifically for 2022–2025 Toyota RAV4 Limited post-facelift configurations with four pre-molded rear backup radar sensor holes. Before ordering, compare the sensor-hole count and placement, reflector areas, lower bumper profile, mounting locations, and reference numbers with your original part. Non-sensor versions or other trim configurations may use a different rear fascia.

Components Not Included

This listing includes the rear bumper cover fascia shell only. Backup radar sensors, sensor brackets or retainers, reflectors, lower valance or garnish components, reinforcement parts, mounting hardware, and other surrounding rear bumper accessories are not included unless specifically stated in the package contents.

Finish & Installation

The bumper cover is supplied in a black exterior finish. The surface should be inspected before final installation to determine whether additional preparation or refinishing is required. Test-fit the bumper before final installation to verify sensor-hole positioning, reflector alignment, surrounding panel fitment, and mounting locations. Professional installation is recommended for the best finished result.

Packaging & Shape Recovery

Rear bumper covers are large, flexible exterior panels and may experience minor temporary flexing during packaging or transportation. After unpacking, allow the bumper cover to rest at room temperature and return to its natural contour before test-fitting or refinishing.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

Built for 2022–2025 Toyota RAV4 Limited post-facelift models, this aftermarket front bumper cover features two pre-molded front parking radar sensor holes to match the corresponding premium-trim fascia configuration. The shell is formed from durable automotive-grade impact-resistant plastic and supplied in a primed black finish for professional prep and refinishing. Its sensor-ready layout makes it a practical replacement for front bumpers affected by collision damage, cracks, heavy scrapes, deformation, or prior repair work.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Radar & Fitment Check

This bumper cover is intended specifically for 2022–2025 Toyota RAV4 Limited post-facelift configurations with two pre-molded front parking radar sensor holes. Before ordering, compare the sensor-hole count and placement, grille openings, lower fascia profile, side openings, mounting locations, and reference numbers with your original bumper. Non-sensor or other trim-specific front fascia layouts may require a different cover.

Components Sold Separately

This listing includes the front bumper cover fascia shell only. Parking radar sensors, sensor brackets or retainers, grille components, side bezels or inserts, reinforcement parts, lighting components, emblems, mounting hardware, and other surrounding bumper accessories are not included unless specifically stated in the package contents.

Paint & Installation

The bumper cover is supplied in a primed black, unpainted finish and requires final surface preparation, color matching, and professional painting before installation. Test-fit the fascia before paintwork to verify sensor-hole positioning, grille alignment, and mounting-point fitment. Professional refinishing and installation are recommended for the best final result.

Packaging & Handling

Because front bumper covers are large, flexible exterior panels, minor temporary flexing may occur during packaging or transportation. After unpacking, allow the bumper cover to rest at room temperature and recover its natural contour before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, radar configuration, and existing components before purchase.

Product Overview

The rear bumper plays an important role in protecting your Honda HR-V while preserving its clean, modern crossover styling. If your original bumper has been damaged by a parking lot accident, a low-speed rear-end collision, loading cargo, or everyday driving, replacing the bumper cover is an effective way to restore your vehicle's exterior while maintaining its factory-inspired appearance. This 2019-2022 Honda HR-V Rear Bumper Cover features an OE-style design that follows the original body lines of compatible HR-V models. Finished with a smooth primed surface, it is ready for professional paint preparation and color matching. Once painted and installed, it helps restore the modern rear styling that makes the Honda HR-V one of today's most versatile compact crossover SUVs. Designed for collision repair, cosmetic restoration, and everyday vehicle maintenance, this replacement rear bumper cover provides a practical and cost-effective solution for replacing a cracked, scratched, or damaged rear bumper while maintaining the clean appearance of your HR-V.

Inspired by the Original HR-V Design

The Honda HR-V combines compact dimensions with SUV versatility, making it an excellent choice for urban driving and everyday adventures. This OE-style replacement rear bumper cover is designed to restore the original rear styling after accident damage or everyday wear, helping your HR-V retain its factory-inspired appearance.

Why Replace a Damaged Rear Bumper Cover?

The rear bumper is one of the most frequently damaged exterior components on a vehicle. Parking mishaps, low-speed impacts, loading cargo, and everyday driving can leave visible scratches, dents, cracks, or scuffs that affect your HR-V's overall appearance.

Replacing a damaged bumper cover can help:

• Restore your vehicle's original appearance

• Replace cracked or damaged bumper surfaces

• Improve overall exterior presentation

• Support rear-end collision repairs

• Complete cosmetic restoration projects

• Prepare your vehicle for resale or trade-in

For many vehicle owners, replacing a damaged bumper cover is often more practical and economical than repairing heavily damaged plastic components.

Primed Surface Ready for Paint

This bumper cover arrives with a smooth primed finish that simplifies the refinishing process.

Benefits include:

• Easier paint preparation

• Professional color matching

• Consistent surface quality

• Reduced preparation time before painting

• Smooth foundation for a factory-quality finish

Professional painting and color matching are recommended for the best appearance after installation.

Common Repair Applications

This rear bumper cover is commonly used for:

• Rear-end collision repair

• Parking damage restoration

• Cosmetic bumper replacement

• Insurance claim repairs

• Exterior body repair projects

• Daily driver maintenance

• Vehicle reconditioning before resale

Whether you're repairing collision damage or restoring your HR-V's appearance, this replacement rear bumper cover helps complete a professional-quality repair.

Product Features

• OE-style rear bumper cover replacement
• Precision-molded to complement factory body lines
• Durable automotive-grade construction
• Smooth primed finish ready for paint
• Ideal for collision repair and exterior restoration
• Helps restore original rear-end styling
• Suitable for professional body shop or DIY repair projects

Important Information

This listing includes one primed rear bumper cover only. Reflectors, parking sensors, mounting hardware, brackets, reinforcement components, trim pieces, and other accessories are sold separately unless otherwise specified.

FAQS

1. Does this rear bumper cover come painted?

No. This rear bumper cover is supplied in a smooth primed finish and must be professionally painted before installation to match your vehicle's color.

2. What is included with this bumper cover?

This listing includes one primed rear bumper cover only. Reflectors, parking sensors, mounting hardware, brackets, reinforcement bars, trim pieces, and other accessories are sold separately unless otherwise specified.

3. Is this an OEM Honda part?

No. This is an aftermarket replacement rear bumper cover designed for compatible Honda HR-V applications. It is manufactured to provide an OE-style appearance and fit.

4. Is professional installation recommended?

Yes. Professional installation is recommended to ensure proper alignment, paint preparation, and a factory-quality finish.

5. Is this bumper cover suitable for collision repair?

Yes. This bumper cover is commonly used for rear-end collision repairs, cosmetic restoration projects, insurance claim repairs, and everyday body repair work.

6. Can this bumper cover be painted to match my vehicle?

Yes. The primed surface is specifically designed for professional paint preparation and color matching to achieve a seamless factory-inspired appearance.

7. Will this rear bumper cover arrive folded?

Some bumper covers may be folded for shipping to reduce shipping costs. The bumper cover will typically return to its original shape after unpacking and standard installation procedures.

Compatibility Disclaimer

Honda® and HR-V® are registered trademarks of Honda Motor Co., Ltd. Velnox Auto is not affiliated with, endorsed by, sponsored by, or otherwise connected to Honda Motor Co., Ltd. Vehicle manufacturer names, model names, trim levels, and model years are used solely for product identification and compatibility purposes. This product is an aftermarket replacement part and is not manufactured, authorized, or approved by Honda Motor Co., Ltd.

Product Overview

The front bumper is one of the most noticeable exterior components of your Honda HR-V, helping protect your vehicle while enhancing its clean, modern appearance. If your original bumper has been damaged by a parking lot incident, road debris, or a minor collision, replacing the bumper cover is an effective way to restore your vehicle's exterior while maintaining its factory-inspired styling. This 2019-2022 Honda HR-V Front Bumper Cover features an OE-style design that follows the original body lines of compatible HR-V models. Finished with a smooth primed surface, it is ready for professional paint preparation and color matching. Once painted and installed, it helps restore the modern front-end styling that makes the Honda HR-V one of today's most versatile compact crossover SUVs. Designed for collision repair, cosmetic restoration, and everyday vehicle maintenance, this replacement front bumper cover provides a practical and cost-effective solution for replacing a cracked, scratched, or damaged bumper while preserving the clean appearance of your HR-V.

Inspired by the Original HR-V Design

The Honda HR-V combines compact dimensions with SUV versatility, making it an ideal choice for city driving and everyday adventures. This OE-style replacement front bumper cover is designed to restore the original front-end styling after accident damage or everyday wear, helping your HR-V maintain its factory-inspired appearance.

Why Replace a Damaged Front Bumper Cover?

The front bumper is one of the most exposed exterior components on any vehicle. Daily driving, parking, and road debris can result in scratches, dents, cracks, or other cosmetic damage that affects your HR-V's appearance.

Replacing a damaged bumper cover can help:

• Restore your vehicle's original appearance

• Replace cracked or damaged bumper surfaces

• Improve overall exterior presentation

• Support front-end collision repairs

• Complete cosmetic restoration projects

• Prepare your vehicle for resale or trade-in

For many vehicle owners, replacing a damaged bumper cover is often more practical and economical than repairing heavily damaged plastic components.

Primed Surface Ready for Paint

This bumper cover arrives with a smooth primed finish that simplifies the refinishing process.

Benefits include:

• Easier paint preparation

• Professional color matching

• Consistent surface quality

• Reduced preparation time before painting

• Smooth foundation for a factory-quality finish

Professional painting and color matching are recommended for the best appearance after installation.

Common Repair Applications

This front bumper cover is commonly used for:

• Front-end collision repair

• Accident damage restoration

• Cosmetic bumper replacement

• Insurance claim repairs

• Exterior body repair projects

• Daily driver maintenance

• Vehicle reconditioning before resale

Whether you're repairing collision damage or restoring your HR-V's appearance, this replacement bumper cover helps complete a professional-quality repair.

Product Features

• OE-style front bumper cover replacement
• Precision-molded to complement factory body lines
• Durable automotive-grade construction
• Smooth primed finish ready for paint
• Ideal for collision repair and exterior restoration
• Helps restore original front-end styling
• Suitable for professional body shop or DIY repair projects

Important Information

This listing includes one primed front bumper cover only. Grilles, emblems, fog lights, parking sensors, mounting hardware, brackets, reinforcement components, and other accessories are sold separately unless otherwise specified.

FAQS

1. Does this front bumper cover come painted?

No. This front bumper cover is supplied in a smooth primed finish and must be professionally painted before installation to match your vehicle's color.

2. What is included with this bumper cover?

This listing includes one primed front bumper cover only. Grilles, emblems, fog lights, parking sensors, mounting hardware, brackets, reinforcement bars, trim pieces, and other accessories are sold separately unless otherwise specified.

3. Is this an OEM Honda part?

No. This is an aftermarket replacement front bumper cover designed for compatible Honda HR-V applications. It is manufactured to provide an OE-style appearance and fit.

4. Is professional installation recommended?

Yes. Professional installation is recommended to ensure proper alignment, paint preparation, and a factory-quality finish.

5. Is this bumper cover suitable for collision repair?

Yes. This bumper cover is commonly used for front-end collision repairs, cosmetic restoration projects, insurance claim repairs, and everyday body repair work.

6. Can this bumper cover be painted to match my vehicle?

Yes. The primed surface is specifically designed for professional paint preparation and color matching to achieve a seamless factory-inspired appearance.

7. Will this front bumper cover arrive folded?

Some bumper covers may be folded for shipping to reduce shipping costs. The bumper cover will typically return to its original shape after unpacking and standard installation procedures.

Compatibility Disclaimer

Honda® and HR-V® are registered trademarks of Honda Motor Co., Ltd. Velnox Auto is not affiliated with, endorsed by, sponsored by, or otherwise connected to Honda Motor Co., Ltd. Vehicle manufacturer names, model names, trim levels, and model years are used solely for product identification and compatibility purposes. This product is an aftermarket replacement part and is not manufactured, authorized, or approved by Honda Motor Co., Ltd.

Product Overview

Restore a damaged rear end with this OE-style Rear Bumper Cover Fascia Bare Shell, designed as a standalone aftermarket replacement for post-facelift Honda Civic Sedan applications. Constructed from flexible automotive-grade plastic, the panel follows the original-style rear body contour and compatible mounting layout. It is supplied in a primed, unpainted finish for professional paint preparation and color matching.

Package Includes

This listing includes the rear bumper fascia main shell only.

The following components are NOT included:

• Continuous rear lower valance / lower lip

• Rear corner bezels or garnish pieces

• Reflectors or related lighting components

• Side retainers, brackets, clips, or installation hardware

• Additional rear bumper trim unless specifically stated

Compatible original components may be reused when applicable or replaced separately as needed.

Paint & Installation Notice

The bumper cover requires professional surface preparation, color matching, and final paint before installation. Always test fit before painting, drilling, cutting, or permanent modification to verify panel alignment and mounting points. Previous collision damage, worn retainers, damaged brackets, or distorted mounting areas may affect installation and should be inspected before fitting the replacement panel. Professional body-shop preparation and installation are recommended. Painted, installed, drilled, cut, damaged, or permanently modified products may not qualify for return under the VELNOX Auto Return Policy.

Folded Shipping & Unboxing Notice

Because of its flexible construction, the bumper cover may be professionally folded and securely packed inside a reinforced shipping carton to help reduce oversized-carrier shipping costs. Temporary bends, waves, creases, or packaging impressions may appear after unpacking and do not necessarily indicate permanent damage.

After unpacking:

1. Remove all protective packaging.

2. Place the bumper cover in a warm, clean area.

3. Allow sufficient time for the panel to recover its molded shape.

4. Apply low, controlled heat gradually and evenly only if necessary.

5. Confirm shape recovery before test fitting and paint preparation.

Avoid concentrated direct heat, open flame, or overheating, as excessive heat may damage the primer or permanently deform the panel.

Before Ordering

Compare Partslink HO1100311, OEM 04715-TBA-A10ZZ, the rear fascia design, and mounting locations with the original bumper before purchase. Confirm that the required lower valance, corner bezels, retainers, and related trim components are available for reuse or separate replacement.

Compatibility Disclaimer

This product is an aftermarket replacement and is not manufactured or supplied by Honda Motor Co., Ltd. OEM reference numbers, North American interchange numbers, vehicle names, trim names and body-style descriptions are provided solely for product identification and compatibility verification. Their use does not indicate that this product is a genuine Honda OEM part. Honda®, Civic® and related trademarks are the property of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by or authorized by Honda Motor Co., Ltd.

Product Overview

Restore the front end with this OE-style Front Bumper Cover Bare Shell, designed as an aftermarket replacement for compatible North American 2019–2021 Honda Civic Sedan and Coupe facelift models. Constructed from flexible automotive-grade plastic, the bumper cover follows the original-style body contour and mounting layout. It is supplied in a primed matte-black finish and requires professional preparation and painting before installation.

Package Includes

The following components are NOT included:

• Upper grille or chrome grille garnish

• Center lower honeycomb grille inserts

• Fog-light bezels or side bumper trim

• Fog lights, bulbs, wiring, or connectors

• Lower chin spoiler or splitter

• Front emblem or license-plate bracket

• Parking sensors or sensor brackets

• Impact absorber or reinforcement beam

• Side mounting brackets

• Clips, retainers, fasteners, or installation hardware

Compatible original components may be transferred from the existing bumper assembly when applicable.

Fitment & Ordering Notice

Designed for compatible North American 2019–2021 Honda Civic Sedan and Coupe facelift models using the matching bumper design.

Applicable body styles:

• Sedan — 4-Door

• Coupe — 2-Door

Applicable configurations may include LX, EX, EX-L, Sport, and Touring.

Does NOT fit:

• Hatchback models

• Type R models

• 2016–2018 pre-facelift models

Before ordering, verify the vehicle year, body style, trim configuration, bumper design, mounting locations, OEM 04711-TBA-A60ZZ, and Partslink HO1000314. Refer to the vehicle fitment chart for complete compatibility information.

Finish & Installation

The bumper cover is supplied primed and unpainted. Professional surface preparation may include cleaning, sanding, primer correction where needed, color matching, and final painting. Primer shade and appearance may vary slightly between production batches. Always test fit the bumper cover and transferred components before painting, drilling, cutting, or permanent modification. Professional installation is recommended. Previous collision damage, worn brackets, or misaligned mounting points may require repair or adjustment before installation. Painted, installed, drilled, cut, damaged, or permanently modified products may not qualify for return under the VELNOX Auto Return Policy.

Folded Shipping & Unboxing Notice

Due to its flexible construction, the bumper cover may be folded-packed inside a reinforced shipping carton to help reduce oversized shipping costs. Temporary bends, waves, or packaging impressions may appear after unpacking and do not necessarily indicate permanent damage.

After Unpacking

1. Remove all protective packaging.

2. Place the bumper cover in a warm, clean area.

3. Allow the panel time to recover its original shape.

4. Apply low, controlled heat gradually and evenly only if necessary.

5. Confirm proper shape and alignment before paint preparation.

Avoid concentrated or excessive heat, which may damage the primer or deform the panel.

Compatibility Disclaimer

This product is an aftermarket replacement component and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, model years, trim names, and body-style descriptions are provided solely for product identification and compatibility verification. Honda® and Civic® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Product Overview

Restore the rear-end appearance of your Honda Civic with this OE-style Rear Bumper Cover Fascia Bare Shell. Designed as a standalone replacement panel for collision repair or exterior restoration, this bumper cover follows the original-style shape and mounting layout for a clean replacement installation.

Package Includes

Product Features

• OE-style replacement rear bumper fascia

• Durable automotive-grade plastic construction

• Factory-style shape and mounting locations

• Suitable for collision repair and exterior restoration

• Designed for professional paint preparation and color matching

• Ideal replacement for cracked, dented, scratched, or damaged bumper covers

This listing is for the Rear Bumper Cover Bare Shell ONLY.

The following components are not included:

• Rear lower valance / diffuser trim

• Reflectors

• Bumper retainers or mounting hardware

• Additional rear bumper trim or accessories unless specifically stated

Compatible original components may be reused where applicable.

Paint & Installation Notice

The bumper cover is supplied primed and unpainted and requires paint preparation and color matching before final installation. Professional installation is recommended. Always test fit before painting to verify alignment and mounting points. Normal surface preparation may be required before painting. Existing mounting components or previously damaged areas may also require adjustment or replacement.

Important Ordering Notice

Before ordering, compare Partslink HO1100287, OEM 04715-TBA-A00ZZ, bumper design, and mounting locations with your original part. Only the component listed under Package Includes is included with your purchase.

Compatibility Disclaimer

This product is an aftermarket replacement component and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, trim names, and body-style descriptions are provided solely for product identification and compatibility verification. Honda® and Civic® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Product Overview

Restore a damaged front end with this OE-style Front Bumper Cover Fascia Bare Shell. Designed as a standalone replacement panel for collision repair or exterior restoration, this bumper cover follows the original-style shape and mounting layout for a clean replacement installation.

Package Includes

This listing is for the Front Bumper Cover Bare Shell ONLY.

The following components are not included:

• Front upper grille

• Fog light bezels / covers

• Additional trim or accessories unless specifically stated

Compatible original components may be reused where applicable.

Paint & Installation Notice

The bumper cover is supplied primed and unpainted and requires paint preparation and color matching before final installation. Professional installation is recommended. Always test fit before painting to verify alignment and mounting points. Existing mounting components or previously damaged areas may require adjustment or replacement.

Important Ordering Notice

Before ordering, compare Partslink HO1000302, OEM 04711-TGG-A00ZZ, bumper design, and mounting locations with your original part. Only the component listed under Package Includes is included with your purchase.

Compatibility Disclaimer

This product is an aftermarket replacement component and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, trim names, and body-style descriptions are provided solely for product identification and compatibility verification. Honda® and Civic® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Restore the clean, factory-style rear appearance of your Honda Accord with this replacement rear bumper cover fascia. Designed for the updated facelift rear-end layout, it is ideal for replacing a cracked, scraped, dented, or collision-damaged bumper cover.

Package Includes

• 1x Rear Bumper Cover Fascia Bare Shell

• Primed finish

• Interchange Number: HO1100318

• OEM Reference Number: 71501-TVA-A10ZZ

This listing includes the rear bumper cover bare shell only.

Lower valance or diffuser skirt, chrome exhaust outlet bezels, tailgate center license-plate garnish, rear reflector lamps, parking sensors, reinforcement components, retainers, brackets, and mounting hardware are not included. Compatible original components may need to be transferred from the existing bumper or purchased separately.

Important Compatibility Note

Designed for the 2021–2022 Honda Accord facelift rear bumper configuration. This part does not fit 2018–2020 pre-facelift models, which use a different bumper structure, exhaust-area layout, lower-valance mounting system, and surrounding trim configuration.

Paint and Installation Notice

The bumper cover is supplied with a primed finish and requires professional surface preparation and paint matching before installation. Test-fit the bumper and confirm all openings, mounting points, and trim connections before painting or modifying the part. Professional body-shop installation is strongly recommended. Minor primer variations or light handling marks may occur during manufacturing and shipping and are normally corrected during standard refinishing.

Compatibility Disclaimer

This product is an aftermarket replacement component and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, model names, trim names, and other identifiers are provided solely for product identification and compatibility-reference purposes. All reference numbers are intended to assist customers in verifying vehicle compatibility and selecting the correct replacement component before purchase. Honda® and Accord® are registered trademarks of Honda Motor Co., Ltd. Trim and configuration names are used solely to identify compatible vehicle applications. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Restore your Honda Accord’s clean, factory-style appearance with this replacement front bumper cover fascia. Designed for the updated facelift body layout, it is ideal for replacing a cracked, scraped, dented, or collision-damaged bumper cover. Its revised design features the wider center grille opening and streamlined side openings used on the facelift front fascia.

Package Includes

• 1x Front Bumper Cover Fascia Bare Shell

• North American Interchange Number: HO1000319

• OEM Reference Number: 71101-TVA-A50ZZ

• Hollander Reference Number: 105-10334

This listing includes the front bumper cover bare shell only.

Grilles, trim moldings, fog-light components, sensors, radar equipment, tow-hook cover, lower spoiler, reinforcement beam, absorber, retainers, brackets, splash shields, license-plate bracket, and mounting hardware are not included. Compatible original components may be transferred from the existing bumper when applicable.

Important Compatibility Note

Designed exclusively for the 2021–2022 facelift front bumper layout. This part does not fit 2018–2020 Honda Accord pre-facelift models, which use a different bumper shape, grille layout, mounting-tab pattern, inner support structure, and surrounding trim configuration.

Paint and Installation Notice

Professional test fitting, surface preparation, painting, and installation are strongly recommended. Confirm the bumper shape, openings, mounting points, and reference numbers before painting or modifying the part. Minor primer variations or light handling marks may occur during manufacturing and shipping and are normally corrected during standard body-shop preparation.

Compatibility Disclaimer

This product is an aftermarket replacement component and is not a genuine Honda OEM product. OEM reference numbers, North American interchange numbers, vehicle names, model names, and trim names are provided solely for product identification and compatibility-reference purposes. Honda® and Accord® are registered trademarks of Honda Motor Co., Ltd. Trim names are used only to identify compatible vehicle configurations. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd.

Product Overview

Replace your damaged rear bumper with this Rear Bumper Cover Assembly for 2020–2022 Honda CR-V North American models. Featuring an integrated upper and lower shell, this assembly provides a complete replacement for the original bumper cover while maintaining the vehicle's original appearance. The upper bumper cover is supplied in a primed black finish for sanding, preparation, and painting, while the lower section features a textured black finish that closely matches the factory appearance. Combining both sections into a single assembly simplifies replacement and eliminates the need to purchase the upper and lower bumper covers separately.

Product Highlights

• Complete upper and lower integrated bumper cover assembly

• Primed upper bumper cover ready for paint

• Factory-style textured black lower section

• Designed for 2020–2022 Honda CR-V North American models

• Direct replacement for the original bumper cover assembly

Reference Numbers

What's Not Included

The following items are not included:

• Rear lower valance trim

• Rear bumper reflectors

• Mounting clips, screws, bolts, and other installation hardware

Fitment & Installation

Compatible with 2020–2022 Honda CR-V North American models.

• Supplied with a primed upper bumper cover that requires preparation and painting before installation.

• Test fit all components before painting or final installation.

• Professional installation is recommended.

Compatibility Disclaimer

This is an aftermarket replacement part and is not a genuine Honda OEM product. OEM part numbers, North American interchange numbers, vehicle names, and model names are provided solely for product identification and compatibility-reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, or endorsed by Honda Motor Co., Ltd.

Product Overview

Replace your original bumper cover with an OE-style aftermarket replacement engineered to match the factory design and fit of compatible 2020–2022 Honda CR-V models. Manufactured to follow the original body lines and mounting locations, this Front Upper Bumper Cover is an ideal solution for repairing collision damage, replacing a cracked bumper, or restoring the factory appearance of your vehicle. Manufactured using automotive-grade injection-molded thermoplastic, the bumper cover provides the flexibility and durability expected of modern exterior body components. It is supplied in a primed gray/black finish and is ready for final surface preparation and painting to match your vehicle. Before placing your order, compare your original bumper cover with the reference part numbers below to confirm compatibility.

Reference Part Numbers

• OEM: 04711-TLA-A50ZZ / 71101-TLA-A50ZZ / 04711-TNY-A00ZZ

• Partslink: HO1014106

• Hollander Number: 101-99430X

Package Includes

• 1 × Front Upper Bumper Cover Bare Shell

• Primed Gray/Black Finish

Items Not Included

This listing includes the Front Upper Bumper Cover Bare Shell only. The following original components are not included and should be reused from your existing bumper or purchased separately if replacement is required:

• Lower bumper valance

• Front grille and grille inserts

• Chrome moldings

• Fog light bezels

• Front emblem

• Parking sensors and sensor retainers (if equipped)

• Mounting brackets

• Clips, screws, fasteners, and installation hardware

• Any additional components not specifically listed

Fitment & Installation

This bumper cover is designed exclusively for the 2020–2022 Honda CR-V facelift models. It is not compatible with 2017–2019 models, as Honda redesigned the front bumper assembly, mounting locations, and trim configuration beginning with the 2020 model year. The bumper cover is supplied in a primed finish and must be painted before installation. We recommend performing a complete test fit before sanding, painting, drilling, or making any permanent modifications. Professional painting and installation are recommended to help ensure proper panel alignment, consistent body gaps, and accurate color matching. Products that have been painted, modified, or installed may not be eligible for return under the VELNOX Auto Return Policy.

Compatibility Disclaimer

This is an aftermarket replacement part and is not a genuine Honda OEM product. OEM part numbers, Partslink numbers, Hollander interchange numbers, vehicle names, model names, and other manufacturer references are provided solely for product identification and compatibility-reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, endorsed by, or authorized by Honda Motor Co., Ltd. The use of manufacturer names, trademarks, and reference numbers is for identification purposes only and does not imply any affiliation with or endorsement by the original vehicle manufacturer. Customers are responsible for verifying vehicle compatibility before purchase by reviewing the vehicle application, reference part numbers, and product specifications. If you have any questions regarding fitment, please contact VELNOX Auto before placing your order.

Product Overview

Restore the rear-end appearance of your Honda CR-V with this aftermarket replacement Rear Bumper Cover Fascia. This listing includes the rear bumper cover bare shell in a primed gray or black finish. Constructed from heavy-duty polypropylene plastic, the bumper cover requires professional surface preparation, color matching, and painting before installation.

Package Includes

• 1× Rear Bumper Cover Bare Shell

• Primed gray or black finish

• Partslink Number: HO1100301

• OEM Reference Numbers: 71501-TLA-A00 / 04712-TLY-A00ZZ / 04717-TLY-A00ZZ

• Hollander Number: 190-10142B

• Material: Heavy-Duty Polypropylene Plastic

This listing includes the Rear Bumper Cover Bare Shell ONLY.

The following components are not included:

• Lower valance lip skirt

• Side reflector lamps

• Chrome garnish strips

Existing factory components may need to be transferred from the original bumper assembly or purchased separately as needed.

Paint and Installation Notice

This rear bumper cover is supplied in a primed finish and is not pre-painted. Professional surface preparation, test fitting, color matching, painting, and installation are strongly recommended. Always test-fit the bumper cover before painting, drilling, trimming, or making any modifications. Painted, modified, or installed parts may not be eligible for return.

Compatibility Disclaimer

This is an aftermarket replacement part and is not a genuine Honda OEM product. OEM part numbers, North American interchange numbers, vehicle names, and model names are provided solely for product identification and compatibility reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, or endorsed by Honda Motor Co., Ltd.

Product Overview

Restore the front-end appearance of your vehicle with this Front Upper Bumper Cover Bare Shell. Designed as an OE-style aftermarket replacement for a cracked, dented, damaged, or missing original bumper cover, it follows the original body contours to help restore proper alignment and a clean, factory-inspired appearance. This bumper cover is intended for collision repair, exterior restoration, or replacement of the original front bumper cover on compatible North American-spec 2017–2019 Honda CR-V models.

For product identification and fitment verification, compare the following reference numbers with your original part before ordering:

• OEM Part Number Reference: 04711-TLA-A00ZZ

• North American Interchange Number: HO1000305

OEM and interchange numbers are provided for identification and compatibility-reference purposes only.

What Is Included

• 1 × Front Upper Bumper Cover Bare Shell Only

Brackets, retainers, mounting hardware, sensors, wiring, trim pieces, and other related components are also not included unless specifically stated. Compatible components may need to be transferred from the original bumper assembly or purchased separately. Please review the product images carefully to confirm the exact item included with this listing.

This listing is for the Front Upper Bumper Cover Bare Skin Shell ONLY. Lower bumper balance valance grille, chrome flying wing strip moldings, and fog light bezel covers are NOT included. 100% Fitment Guaranteed ONLY for North American 2017-2019 Pre-Facelift Models (LX, EX, EX-L, Touring). This lightweight flexible plastic bumper panel is folded-packed using high-resiliency security wraps to entirely bypass commercial oversized carrier freight surcharges, directly maximizing your dollar savings. Direct bolt-on replacement. 

Fitment Verification

This bumper cover is designed for compatible North American-spec 2017–2019 Honda CR-V models that match the vehicle configuration and reference numbers listed above. Fitment may vary based on trim level, production date, equipment package, bumper configuration, and previous vehicle modifications. Before ordering, verify the vehicle year, model, trim, original bumper design, OEM reference number, and interchange number.

Before painting or final installation, test-fit the bumper cover and confirm that:

• The mounting points align correctly

• The body contours match the vehicle

• All openings match the original bumper configuration

• Any original components being transferred fit correctly

Do not paint, drill, cut, permanently install, or otherwise modify the bumper cover until fitment has been fully confirmed. Products that have been painted, installed, damaged, or permanently modified may not be eligible for return under the VELNOX Auto Return Policy.

Paint and Installation Notice

This bumper cover is supplied with a primed surface and is not painted to match the vehicle’s exterior color. Test fitting, cleaning, sanding, surface preparation, additional priming, and professional color matching may be required before final painting and installation. As with most primed replacement body panels, standard body-shop preparation may be necessary to achieve the best finish and alignment. Professional painting and body-shop installation are strongly recommended to help ensure proper alignment, secure attachment, and an accurate color match.

FAQS

1. What exactly is included with this listing?

This listing includes one Front Upper Bumper Cover Bare Shell only. It is not a complete bumper assembly and does not include additional exterior components unless specifically stated.

2. Are the grille, fog lights, and emblem included?

No. The grille, fog lights, and emblem are not included. Compatible parts may need to be transferred from the original bumper assembly or purchased separately.

3. How can I confirm that this bumper cover fits my vehicle?

Confirm that your vehicle is a compatible North American-spec 2017–2019 Honda CR-V and compare your original part with:

• OEM Part Number Reference: 04711-TLA-A00ZZ

• North American Interchange Number: HO1000305

You should also verify the trim level, bumper openings, equipment package, and original bumper configuration before ordering.

4. Is the bumper cover already painted?

No. The bumper cover is supplied with a primed surface and requires preparation and painting before final installation. Professional color matching is recommended because paint appearance may vary due to vehicle age, fading, previous repairs, and production differences.

5. Should the bumper cover be test-fitted before painting?

Yes. Always test-fit the bumper cover before painting or making permanent modifications. Confirm the mounting points, openings, body contours, and compatibility of any transferred components before completing the repair.

This listing is for the Bumper Cover Bare Shell ONLY. Grille, fog lights, and emblem are NOT included. 100% Fitment Guaranteed for North American Models.

Compatibility Disclaimer

This is an aftermarket replacement part and is not a genuine Honda OEM product. OEM part numbers, interchange numbers, vehicle names, and model names are used solely for product identification and compatibility-reference purposes. Honda® and CR-V® are registered trademarks of Honda Motor Co., Ltd. VELNOX Auto is not affiliated with, sponsored by, or endorsed by Honda Motor Co., Ltd.

Product Overview

This rear bumper cover is designed for 2022–2025 Toyota RAV4 LE & XLE post-facelift models without factory sensor holes, matching the standard rear fascia configuration used on these trims. Manufactured from durable automotive-grade impact-resistant plastic, the cover is supplied in a primed black finish for professional surface preparation and repainting. It provides a clean replacement solution for rear bumpers affected by cracks, scrapes, deformation, collision damage, or previous repair work.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Fitment Confirmation

This bumper cover is intended specifically for 2022–2025 Toyota RAV4 LE & XLE post-facelift configurations without parking sensor holes. Before ordering, compare the rear bumper profile, reflector locations, lower contour, mounting areas, sensor-hole layout, and reference numbers with your original part. Sensor-equipped versions or other trim configurations may use a different rear fascia.

Parts Not Included

This listing includes the rear bumper cover fascia shell only. Reflectors, lower garnish or valance components, parking sensors, sensor brackets, retainers, reinforcement components, mounting hardware, and other surrounding rear bumper parts are not included unless specifically stated in the package contents.

Paint & Installation

The bumper cover is supplied in a primed black, unpainted finish and requires final surface preparation, color matching, and professional painting before installation. Test-fitting before paintwork is strongly recommended to confirm alignment with the quarter panels, reflector areas, and mounting points. Professional installation is recommended, especially when the vehicle has previous rear collision damage.

Packaging & Shape Recovery

Large bumper fascia panels are flexible by design and may show minor temporary movement in shape while packaged or transported. After unpacking, allow the bumper cover to rest at room temperature and return to its natural contour before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

Designed for the updated 2022–2025 Toyota RAV4 LE & XLE post-facelift front-end configuration, this aftermarket bumper cover offers a clean replacement solution for damaged, cracked, scraped, or previously repaired factory fascia panels. The cover is molded from durable automotive-grade impact-resistant plastic and supplied in a primed black finish for professional prep and refinishing. Its standard-trim profile is intended to match the LE/XLE bumper layout while providing a solid foundation for collision repair or cosmetic restoration.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Fitment Verification

This bumper cover is intended for 2022–2025 Toyota RAV4 LE & XLE post-facelift models using the corresponding standard front bumper configuration. Before ordering, compare the bumper contour, grille openings, side insert areas, mounting locations, and reference numbers with the original part on your vehicle. Other trims may use a different fascia layout.

Components Sold Separately

This listing includes the front bumper cover fascia shell only. Grille assemblies, side bezels or inserts, brackets, retainers, reinforcement components, lighting parts, sensors, emblems, mounting hardware, and other surrounding bumper components are not included unless specifically listed in the package contents.

Paint Preparation & Installation

The supplied primed black finish is intended for professional refinishing and is not the vehicle’s final exterior color. Test-fit the bumper before painting to confirm alignment with the surrounding body panels, grille openings, and mounting points. Proper surface preparation, color matching, painting, and professional installation are recommended.

Packaging & Handling

Automotive bumper covers are flexible exterior panels and may experience minor temporary flexing during packaging or transportation. After unpacking, allow the bumper cover to rest at room temperature and recover its natural contour before test-fitting or beginning refinishing work.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, and existing components before purchase.

Product Overview

This aftermarket rear bumper cover is designed for 2019–2021 Toyota RAV4 Limited pre-facelift models equipped with four rear backup radar sensor holes. Made from durable automotive-grade impact-resistant plastic, the fascia comes in a primed black finish for professional preparation and repainting. Its four pre-molded sensor openings are configured for the corresponding Limited-trim rear bumper layout, making it suitable for collision repair, exterior restoration, or replacement of a damaged original fascia.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Sensor & Fitment Check

This rear bumper cover is intended specifically for 2019–2021 Toyota RAV4 Limited pre-facelift configurations with four pre-molded backup radar sensor holes. Before ordering, compare the sensor-hole count and placement, reflector areas, lower bumper contour, mounting points, and reference numbers with your original part. Non-sensor versions or other trim configurations may use a different rear fascia.

Components Not Included

This listing includes the rear bumper cover fascia shell only. Backup radar sensors, sensor brackets or retainers, reflectors, lower garnish or valance pieces, reinforcement components, mounting hardware, and other surrounding rear bumper parts are not included unless specifically stated in the package contents.

Finish & Installation

The bumper cover is supplied in a primed black, unpainted finish intended for professional refinishing. Test-fit the part before painting to confirm sensor-hole positioning, surrounding component alignment, and mounting-point fitment. Proper surface preparation, color matching, painting, and professional installation are recommended.

Packaging & Shape Recovery

Rear bumper covers are large and flexible exterior panels, so minor temporary flexing may occur during packaging or transportation. After unpacking, allow the bumper cover to rest at room temperature and return to its natural contour before test-fitting, preparation, or painting.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

This aftermarket front bumper cover is configured for 2019–2021 Toyota RAV4 Limited pre-facelift models equipped with two front parking radar sensor holes. Manufactured from durable automotive-grade impact-resistant plastic, the fascia is supplied in a primed black finish for professional preparation and refinishing. The pre-molded dual-sensor layout is intended to match the corresponding Limited-trim front bumper configuration, making it suitable for collision repair, cosmetic restoration, or replacement of a damaged original fascia.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Radar & Fitment Verification

This bumper cover is intended specifically for 2019–2021 Toyota RAV4 Limited pre-facelift configurations with two pre-molded front parking radar sensor holes. Before purchase, compare the sensor-hole count and placement, grille openings, lower fascia profile, side openings, mounting points, and reference numbers with your original bumper. Non-sensor versions or other trim configurations may use a different front fascia.

Components Not Included

This listing includes the front bumper cover fascia shell only. Parking radar sensors, sensor retainers or brackets, grille components, side bezels or inserts, reinforcement parts, lighting components, emblems, mounting hardware, and other surrounding bumper accessories are not included unless specifically stated in the package contents.

Finish & Installation

The bumper cover is supplied with a primed black surface intended for professional painting and refinishing. Test-fit the fascia before paintwork to confirm sensor-hole positioning, grille alignment, and mounting-point fitment. Proper surface preparation, color matching, refinishing, and professional installation are recommended.

Packaging & Handling

Because front bumper fascia panels are large and flexible, minor temporary flexing may occur during packaging or transportation. After unpacking, allow the bumper cover to rest at room temperature and return to its natural contour before test-fitting or beginning paint preparation.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

Restore the rear bodywork of your 2019–2021 Toyota RAV4 LE or XLE with this aftermarket bumper cover, configured for pre-facelift models without factory sensor holes. The fascia is formed from durable automotive-grade impact-resistant plastic and supplied in a primed black finish for professional paint preparation and color matching. It provides a clean replacement option when the original rear bumper has suffered cracks, scrapes, deformation, collision damage, or previous repair work.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Vehicle & Sensor Check

This rear bumper cover is intended for 2019–2021 Toyota RAV4 LE & XLE pre-facelift models without parking sensor holes. Check the original bumper’s sensor layout, reflector locations, lower contour, attachment points, and reference numbers before purchase. Versions equipped with factory sensors or a different trim-specific rear fascia may require another bumper configuration.

Accessories Not Included

Only the rear bumper cover fascia shell is included. Reflectors, lower valance or garnish pieces, parking sensors, sensor brackets, retainers, reinforcement components, installation hardware, and surrounding rear bumper accessories are not included unless specifically stated in the package contents.

Finish & Installation

The primed black surface is preparation-ready and requires final refinishing before installation. Test-fit the bumper first, then complete any necessary surface preparation, paint matching, and final coating. Professional installation is recommended to ensure proper fit around the quarter panels, reflectors, and mounting locations.

Delivery & Shape Recovery

The flexible construction of an automotive bumper fascia may allow minor temporary movement in shape during packaging and transportation. Once unpacked, leave the bumper at room temperature until it returns to its natural contour before beginning fitment checks or paint preparation.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

This aftermarket front bumper cover is made for 2019–2021 Toyota RAV4 LE & XLE pre-facelift models without front sensor holes, providing the correct standard-trim fascia configuration for repair or replacement work. Manufactured from durable automotive-grade impact-resistant plastic, the bumper arrives in a primed black finish ready for professional surface preparation and painting. It is a suitable replacement for original fascia panels affected by collision damage, cracks, deep scratches, deformation, or previous repair work.

Reference Numbers

Package Includes

• 1x Front Bumper Cover Face Matrix Shield Shell

Fitment & Sensor Configuration

This bumper cover is intended for 2019-2021 Toyota RAV4 LE & XLE pre-facelift configurations without pre-molded sensor holes. Before ordering, compare your original bumper’s sensor-hole layout, grille openings, side openings, overall contour, mounting locations, and reference numbers. Sensor-equipped or other trim-specific fascia designs may require a different bumper cover.

Components Sold Separately

This listing includes the front bumper cover fascia shell only. Grille assemblies, side bezels or inserts, sensor components, brackets, retainers, reinforcement parts, lighting components, emblems, mounting hardware, and other surrounding bumper parts are not included unless specifically listed in the package contents.

Paint Preparation & Installation

The supplied primed black surface is intended for professional refinishing and is not a final exterior paint finish. Test-fit the bumper before painting to confirm proper alignment with surrounding panels, grille openings, and mounting locations. Final surface preparation, color matching, painting, and professional installation are recommended.

Packaging & Handling

Front bumper covers are flexible exterior body panels and may experience minor temporary flexing while packaged or transported. After unpacking, allow the bumper to rest at room temperature and regain its normal contour before test-fitting or beginning refinishing work.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.

Product Overview

Designed for 2016–2018 Toyota RAV4 Limited post-facelift models equipped with four rear backup radar sensor holes, this aftermarket rear bumper cover provides the correct premium-trim fascia layout for collision repair or exterior restoration. Molded from durable automotive-grade impact-resistant plastic, the cover is supplied in a primed black finish for professional preparation and painting. The factory-style sensor-hole layout helps simplify reuse or transfer of the corresponding rear parking-assist components when the original bumper has been cracked, scraped, deformed, or impact damaged.

Reference Numbers

Package Includes

• 1x Rear Bumper Cover Face Matrix Shield Shell

Sensor & Fitment Verification

This bumper cover is intended specifically for 2016–2018 Toyota RAV4 Limited post-facelift configurations with four pre-molded rear sensor holes. Before ordering, compare the sensor-hole count and placement, reflector areas, lower bumper contour, mounting points, and reference numbers with your existing part. Non-sensor versions or other trim layouts may require a different rear fascia.

Parts Not Included

This listing includes the rear bumper cover shell only. Parking sensors, sensor retainers or brackets, reflectors, lower garnish or valance components, reinforcement parts, mounting hardware, and other surrounding rear bumper components are not included unless specifically listed in the package contents.

Refinishing & Installation

The bumper cover arrives in a primed black, unpainted finish intended for professional refinishing. Test-fit the part before painting to verify the sensor locations, surrounding component alignment, and mounting points. Final surface preparation, color matching, painting, and professional installation are recommended.

Packaging & Handling

Because rear bumper covers are large and flexible, minor temporary flexing can occur during packaging and transportation. After unpacking, allow the panel to rest at room temperature and recover its normal shape before test-fitting or beginning paint preparation.

Compatibility Disclaimer

This product is an aftermarket replacement part and is not manufactured by, authorized by, sponsored by, endorsed by, or affiliated with Toyota Motor Corporation. Toyota® and RAV4® are registered trademarks of Toyota Motor Corporation. Vehicle names, trademarks, OEM numbers, Partslink numbers, interchange references, Hollander identifiers, and related cross-reference information are used solely for product identification and compatibility purposes. Customers are responsible for confirming compatibility with their specific vehicle, trim level, sensor configuration, and existing components before purchase.